{
  "id": "norm-103603",
  "citation": "Decreto 0-A",
  "section": "norms",
  "doc_type": "regulation",
  "title_es": "Especificación Técnica AyA-6000-TBC-01-A01 Tubería de concreto para conductos pluviales",
  "title_en": "Technical Specification AyA-6000-TBC-01-A01 Concrete Pipe for Storm Drains",
  "summary_es": "Esta especificación técnica del Instituto Costarricense de Acueductos y Alcantarillados (AyA) establece los requisitos que debe cumplir la tubería de concreto de sección circular, con o sin refuerzo, utilizada en sistemas pluviales por gravedad. Define las clases mínimas según la presencia de tránsito vehicular (clase III mínimo, ASTM C76M para reforzada y ASTM C14M para sin refuerzo), requisitos de diámetros, uniones elastoméricas, uso de fibras sintéticas y no sintéticas, color conforme a la normativa de AyA para sistemas pluviales, y rotulado visible e indeleble. También exige certificación de producto por un Organismo Evaluador de la Conformidad y lineamientos para manipulación, almacenamiento y transporte. No aborda temas de seguridad ocupacional ni gestión de riesgos.",
  "summary_en": "This technical specification from the Costa Rican Institute of Aqueducts and Sewers (AyA) establishes requirements for circular concrete pipe, with or without reinforcement, used in gravity-fed storm drainage systems. It defines minimum classes based on vehicular traffic (minimum class III, ASTM C76M for reinforced and ASTM C14M for unreinforced), diameter requirements, elastomeric joints, use of synthetic and non-synthetic fibers, color per AyA stormwater standards, and legible, indelible marking. It also mandates product certification by a conformity assessment body and guidelines for handling, storage, and transportation. It does not address occupational safety or risk management.",
  "court_or_agency": "",
  "date": "15/06/2021",
  "year": "2021",
  "topic_ids": [
    "_off-topic"
  ],
  "primary_topic_id": "_off-topic",
  "es_concept_hints": [
    "AyA (Instituto Costarricense de Acueductos y Alcantarillados)",
    "conductos pluviales",
    "escurrimiento libre",
    "tubería de concreto con/sin refuerzo",
    "norma técnica AyA",
    "OEC (Organismo Evaluador de la Conformidad)"
  ],
  "concept_anchors": [
    {
      "article": "N/A",
      "law": "Norma técnica para diseño y construcción de sistemas de abastecimiento de agua potable, de saneamiento y pluvial (AyA)"
    },
    {
      "article": "toda",
      "law": "ASTM C14M-2020"
    },
    {
      "article": "toda",
      "law": "ASTM C76M-2020"
    }
  ],
  "keywords_es": [
    "tubería de concreto",
    "conductos pluviales",
    "AyA",
    "especificación técnica",
    "norma ASTM",
    "drenaje pluvial",
    "infraestructura sanitaria",
    "certificación de producto"
  ],
  "keywords_en": [
    "concrete pipe",
    "storm drains",
    "AyA",
    "technical specification",
    "ASTM standard",
    "storm drainage",
    "sanitary infrastructure",
    "product certification"
  ],
  "excerpt_es": "1. Objeto y campo de aplicación\nEsta especificación establece los requisitos que debe cumplir la tubería de sección circular fabricada en concreto, con o sin refuerzo, para uso en el trasiego de agua por gravedad en sistemas pluviales.\n\nEsta norma no contempla requisitos relacionados con seguridad y salud ocupacional, ni con la gestión o administración del riesgo inherente al objeto normado o que pueda derivarse una vez instalado.",
  "excerpt_en": "1. Purpose and scope\nThis specification establishes the requirements for circular-section pipe made of concrete, with or without reinforcement, for use in gravity-flow stormwater systems.\n\nThis standard does not include requirements related to occupational health and safety, nor to the management or administration of risk inherent to the regulated object or that may arise once installed.",
  "outcome": {
    "label_en": "Active technical standard",
    "label_es": "Norma técnica vigente",
    "summary_en": "Establishes technical requirements for circular concrete pipe with or without reinforcement used in gravity stormwater systems, including classes, diameters, joints, fibers, color and marking, with mandatory product certification.",
    "summary_es": "Establece los requisitos técnicos para tubería de concreto circular con o sin refuerzo en sistemas pluviales por gravedad, incluyendo clases, diámetros, juntas, fibras, color y rotulado, con exigencia de certificación de producto."
  },
  "pull_quotes": [
    {
      "context": "Requisito 4.1.2",
      "quote_en": "In vehicular traffic areas, reinforced concrete pipe meeting ASTM C76M, class III minimum, must be used.",
      "quote_es": "En zonas de tránsito vehicular, se debe utilizar tubería de concreto reforzado que cumpla con la norma ASTM C76M, clase III como mínimo."
    },
    {
      "context": "Requisito 4.1.2",
      "quote_en": "In areas without vehicular traffic, unreinforced concrete pipe meeting ASTM C14M, class III minimum, must be used.",
      "quote_es": "En las zonas donde no exista tránsito vehicular, se debe utilizar tubería de concreto sin refuerzo que cumpla con la norma ASTM C14M, clase III como mínimo."
    },
    {
      "context": "Requisito 4.2.2",
      "quote_en": "Buttering the bells manufactured for pipe-to-pipe connections with elastomeric joints is not permitted.",
      "quote_es": "No se permite solaquear las campanas fabricadas para unión tubo-tubo con junta elastomérica."
    }
  ],
  "cites": [],
  "cited_by": [],
  "references": {
    "internal": [],
    "external": []
  },
  "source_url": "https://pgrweb.go.cr/scij/Busqueda/Normativa/Normas/nrm_texto_completo.aspx?param1=NRTC&nValor1=1&nValor2=103603&strTipM=TC&nValor3=0",
  "tier": 2,
  "_editorial_citation_count": 0,
  "regulations_by_article": null,
  "amendments_by_article": null,
  "dictamen_by_article": null,
  "concordancias_by_article": null,
  "afectaciones_by_article": null,
  "resoluciones_by_article": null,
  "cited_by_votos": [],
  "cited_norms": [],
  "cited_norms_inverted": [],
  "sentencias_relacionadas": [],
  "temas_y_subtemas": [],
  "cascade_only": false,
  "amendment_count": 0,
  "body_es_text": "en la totalidad del texto\n\n                    -\n\n                        Texto Completo Norma 0\n\n                        Especificaciones Técnicas AyA-6000-TBC-01-A01 Tubería de concreto con o sin\nrefuerzo para conductos pluviales en escurrimiento libre\n\nINSTITUTO COSTARRICENSE\nDE ACUEDUCTOS Y ALCANTARILLADOS\n\nEspecificación Técnica\n\nAyA-6000-TBC-01-A01\n\nTUBERÍA DE CONCRETO CON\nO SIN REFUERZO PARA CONDUCTOS\n\nPLUVIALES EN\nESCURRIMIENTO LIBRE. PARTE 1: REQUISITOS DE LA\n\nTUBERÍA DE CONCRETO DE\nSECCIÓN CIRCULAR\n\n1.\nObjeto y campo de aplicación\n\nEsta\nespecificación establece los requisitos que debe cumplir la tubería de sección\ncircular fabricada en concreto, con o sin refuerzo, para uso en el trasiego de\nagua por gravedad en sistemas pluviales.\n\nEsta norma\nno contempla requisitos relacionados con seguridad y salud ocupacional, ni con\nla gestión o administración del riesgo inherente al objeto normado o que pueda\nderivarse una vez instalado.\n\n2. Términos\ny definiciones\n\nSon de\naplicación las definiciones que se indican en la \"Norma técnica para\ndiseño y construcción de sistemas de abastecimiento de agua potable, de\nsaneamiento y pluvial\" de AyA ó en las normas técnicas que se referencian\nen esta especificación.\n\n3.\nSiglas\n\nA\ncontinuación se detallan los nombres de los organismos y las abreviaturas de\nlos códigos normativos que se citan en la presente especificación: ASTM\nAmerican Society for Testing Materials INTECO Instituto de Normas Técnicas de\nCosta Rica OEC Organismo de Evaluación de la Conformidad\n\n4.\nRequisitos técnicos\n\n4.1.\nRequisito general\n\n4.1.1.\nSistema de dimensionamiento\n\nLa\nselección de la tubería de concreto debe considerar el valor real de su\ndiámetro interno, así mismo, debe tomarse en consideración que la norma de\nfabricación del tubo (norma técnica de producto) establece una categorización\npor diámetro interno, espesor mínimo y resistencia del concreto, denominada\n\"clase\".\n\nCada norma\nde fabricación determina el dimensionamiento del tubo según diámetro nominal\ninterno o diámetro interno de diseño, en ambos casos se debe identificar el\nvalor real del diámetro interno y las variaciones permitidas.\n\n4.1.2.\nClase en tubería con o sin refuerzo\n\nEn zonas de\ntránsito vehicular, se debe utilizar tubería de concreto reforzado que cumpla\ncon la norma ASTM C76M, clase III como mínimo. El diseñador debe realizar el\nanálisis de las condiciones de proyecto que determine el requerimiento de una\nclase mayor para la tubería con refuerzo.\n\nEn las\nzonas donde no exista tránsito vehicular, se debe utilizar tubería de concreto\nsin refuerzo que cumpla con la norma ASTM C14M, clase III como mínimo.\n\n4.2.\nRequisitos específicos\n\n4.2.1.\nDiámetro\n\nSe acepta\nel uso de tubería según las normas de fabricación ASTM C14M y ASTM C76M, en el\ntrasiego de agua por gravedad en sistemas pluviales, en los diámetros definidos\nen la Norma Técnica de Diseño y Construcción de Sistemas de Abastecimiento de\nAgua Potable, de Saneamiento y Pluvial, con las salvedades o excepciones\nestablecidas en dicha norma técnica emitida por AyA, incluido lo relacionado\ncon sus aplicaciones en sistemas pluviales Cuando el diámetro requerido no se\nespecifique en la norma o se requiera un tubo con otros criterios de diseño, se\ndebe confirmar con el fabricante el rango comercial de productos disponibles, y\nde requerirse un diseño particular se debe evaluar el costo y el tiempo de\nfabricación asociado, al ser un producto que se diseña bajo condiciones\nespeciales.\n\nEl tubo que\nse fabrique con un diseño modificado, también debe cumplir con la norma de\nfabricación ASTM C14M ó ASTM C76M, según corresponda.\n\n4.2.2.\nUnión \"tubo-tubo\"\n\nEn relación\ncon la junta elastomérica, para el tubo de concreto con refuerzo aplican los\nrequisitos establecidos en la norma de fabricación del tubo, para lo cual el\ndiseñador deberá seleccionar la junta siempre que cumpla con alguna de las\nsiguientes normas: ATSM C443, ASTM C990 y ASTM C1628.\n\nEn el caso\nparticular de la junta elastomérica del tubo de concreto sin refuerzo, ésta\ndebe cumplir con la norma ASTM C443.\n\nNo se\npermite solaquear las campanas fabricadas para unión tubo-tubo con junta\nelastomérica.\n\n4.2.3.\nFibras sintéticas y no sintéticas\n\nSe permite\nincluir fibras en la mezcla para tubo de concreto con o sin refuerzo, siempre\nque éstas sean del tipo II o III sin son \"sintéticas\", o del tipo I\nsi son \"no sintéticas\", de conformidad con los requisitos señalados\nen la norma de fabricación del tubo, sea ASTM C14M o ASTM C76M según\ncorresponda.\n\nEn todos\nlos casos las fibras deben cumplir con los requisitos de la norma INTE C31\n(INTE 06-01-20), como material de fabricación no estructural.\n\nCuando el\ntubo incorpore fibras sintéticas o no sintéticas que cumplan con los requisitos\nseñalados, se debe aportar una certificación emitida por el fabricante del\ntubo, en donde se señale para cada tipo de fibra, lo siguiente:\n\n. Tipo,\nnombre y composición de la fibra.\n\n. Nombre y\ncódigo de la norma de fabricación para cada tipo de fibra.\n\n. Método de\nadición de la fibra al concreto.\n\n. Detalle\nexplicativo del aporte al funcionamiento o desempeño esperado del tubo, al\nincorporar la fibra como material no estructural.\n\n4.2.4.\nColor\n\nEl color\ndel tubo debe cumplir con lo establecido para sistemas pluviales, de\nconformidad con la \"Norma técnica para diseño y construcción de sistemas\nde abastecimiento de agua potable, de saneamiento y pluvial\" de AyA.\n\nPor lo\nanterior, queda sin efecto toda referencia o requisito de color incluido en las\nnormas técnicas de producto a las que se haga referencia de forma directa o\nindirecta en la presente especificación.\n\n4.2.5.\nRotulado\n\nCada tubo\ndebe cumplir con el requerimiento de rotulado establecido en la norma técnica\nde fabricación respectiva (norma técnica de producto), cuyos caracteres deben\nser totalmente visibles, legibles e indelebles, para garantizar la correcta\nidentificación de la tubería durante y después de la instalación.\n\n5.\nDisposiciones complementarias\n\n5.1.\nCertificaciones de producto\n\nEs de\naplicación el requisito de certificación del producto emitido por un Organismo\nEvaluador e la Conformidad (OEC), organismo de tercera parte, en los términos\nque se establecen en la \"Norma técnica para diseño y construcción de\nsistemas de abastecimiento de agua potable, de saneamiento y pluvial\" de\nAyA.\n\nEn la\noferta técnica se debe aportar la certificación de producto del tubo respecto a\nla norma de fabricación con la que cumple, siendo aceptables únicamente la ASTM\nC14M ó ASTM C76M, según corresponda.\n\n5.2.\nManipulación, almacenamiento y transporte\n\nEn la\noferta técnica se debe incorporar un capítulo de \"Manipulación,\nalmacenamiento y transporte\", donde se detallen las acciones y\nrecomendaciones de parte del o los fabricantes para el adecuado manejo,\ntransporte y almacenamiento de los tubos; lo anterior, según sea requerido de\nprevio o durante el proceso de construcción, a efecto de garantizar su\nfuncionalidad y vida útil.\n\nAsí mismo,\nse deben incluir en este capítulo toda disposición, que para tales efectos, se\nindiquen en las normas técnicas de fabricación aplicables a la tubería.\n\n6.\nDocumentos normativos de referencia\n\nLas normas\nque se citan en este apartado forman parte integral de los requisitos técnicos\nincluidos en este documento. Las ediciones indicadas estaban en vigencia al\nmomento de formular la presente especificación:\n\nAcuerdo\nJunta Directiva AyA Nº 2017-281 \"Norma técnica para diseño y construcción\nde sistemas de abastecimiento de agua potable, de saneamiento y pluvial\".\nPublicado en el ALCANCE N º 227 A,B,C,D,E,F,G de La Gaceta Nº 180 del 22 de\nsetiembre del 2017\n\nASTM\nC14M-2020 \"Standard Specification for Nonreinforced Concrete Sewer, Storm\nDrain, and Culvert Pipe (Metric)\"\n\nASTM\nC1628-2019 \"Standard Specification for Joints for Concrete Gravity Flow\nSewer Pipe, Using Rubber Gaskets\"\n\nASTM\nC443-2020 \"Standard Specification for Joints for Concrete Pipe and\nManholes, Using Rubber Gaskets\"\n\nASTM\nC76M-2020 \"Standard Specification for Reinforced Concrete Culvert, Storm\nDrain, and Sewer Pipe (Metric)\" ASTM C990-09 (reaprobada 2019)\n\n\"Standard\nSpecification for Joints for Concrete Pipe, Manholes, and Precast Box Sections\nUsing Preformed Flexible Joint Sealants\"\n\nINTE\nC31:2016 \"Fibra de refuerzo de concreto. Especificaciones\"\n\nEn caso de\nque una norma sea actualizada por el emisor de forma posterior a la entrega de\nla oferta técnica o durante el proceso de suministro o instalación, el\ncontratante y el contratista deben revisar si los requisitos contenidos en la\nnorma mantienen su aplicación, dentro del alcance de la presente especificación\ntécnica.\n\nLos códigos\nde las normas nacionales que se indican entre paréntesis y que contienen el\ncódigo \"INTE\", corresponden a la codificación anteriormente\nestablecida por el Instituto de Normas Técnicas de Costa Rica (INTECO).\n\n7. Anexos (normativos e\ninformativos)\n\nEl presente\ndocumento no contiene anexos normativos ni informativos.\n\n8.\nBibliografía\n\nLos\nrequisitos que se integran en esta especificación técnica, se sustentan en\ncriterios técnicos según ámbitos de competencia y en documentos normativos de\nreferencia.\n\n9.\nDescriptores\n\nConcreto;\ntubería y accesorios.\n\n10. Control de versiones",
  "body_en_text": "in the entirety of the text\n\n                    -\n\n                        Complete Standard Text 0\n\n                        Technical Specifications AyA-6000-TBC-01-A01 Concrete pipe with or without\nreinforcement for storm drains in free flow\n\nCOSTA RICAN INSTITUTE\nOF AQUEDUCTS AND SEWERS\n\nTechnical Specification\n\nAyA-6000-TBC-01-A01\n\nCONCRETE PIPE WITH\nOR WITHOUT REINFORCEMENT FOR STORM\n\nDRAINS IN\nFREE FLOW. PART 1: REQUIREMENTS FOR\n\nCIRCULAR SECTION\nCONCRETE PIPE\n\n1.\nPurpose and scope\n\nThis\nspecification establishes the requirements that must be met by circular section\npipe manufactured in concrete, with or without reinforcement, for use in the\nconveyance of water by gravity in storm systems.\n\nThis standard\ndoes not contemplate requirements related to occupational health and safety, nor to\nthe management or administration of the risk inherent to the standardized object or that may arise once installed.\n\n2. Terms\nand definitions\n\nThe definitions indicated in the \"Technical standard for the design and construction of potable water supply, sanitation, and storm systems\" of AyA or in the technical standards referenced in this specification apply.\n\n3.\nAcronyms\n\nThe names of the organizations and the abbreviations of the normative codes cited in this specification are detailed below: ASTM American Society for Testing Materials INTECO Instituto de Normas Técnicas de Costa Rica OEC Conformity Assessment Body (Organismo de Evaluación de la Conformidad)\n\n4.\nTechnical requirements\n\n4.1.\nGeneral requirement\n\n4.1.1.\nSizing system\n\nThe\nselection of the concrete pipe must consider the actual value of its internal diameter, and it must also be taken into consideration that the pipe manufacturing standard (product technical standard) establishes a categorization by internal diameter, minimum wall thickness (espesor mínimo), and concrete strength, called \"class\".\n\nEach manufacturing standard determines the pipe sizing according to nominal internal diameter or design internal diameter; in both cases, the actual value of the internal diameter and the permitted variations must be identified.\n\n4.1.2.\nClass in pipe with or without reinforcement\n\nIn areas of vehicular traffic, reinforced concrete pipe that complies with standard ASTM C76M, class III as a minimum, must be used. The designer must perform the analysis of the project conditions that determines the requirement for a higher class for the reinforced pipe.\n\nIn areas where there is no vehicular traffic, nonreinforced concrete pipe that complies with standard ASTM C14M, class III as a minimum, must be used.\n\n4.2.\nSpecific requirements\n\n4.2.1.\nDiameter\n\nThe use of pipe according to manufacturing standards ASTM C14M and ASTM C76M is accepted, in the conveyance of water by gravity in storm systems, in the diameters defined in the Technical Standard for the Design and Construction of Potable Water Supply, Sanitation, and Storm Systems, with the provisions or exceptions established in said technical standard issued by AyA, including that related to its applications in storm systems. When the required diameter is not specified in the standard or a pipe with other design criteria is required, the commercially available product range must be confirmed with the manufacturer, and if a particular design is required, the cost and associated manufacturing time must be evaluated, as it is a product designed under special conditions.\n\nThe pipe manufactured with a modified design must also comply with the manufacturing standard ASTM C14M or ASTM C76M, as applicable.\n\n4.2.2.\n\"Pipe-to-pipe\" joint\n\nIn relation to the elastomeric joint, for the reinforced concrete pipe, the requirements established in the pipe manufacturing standard apply, for which the designer must select the joint provided it complies with one of the following standards: ATSM C443, ASTM C990, and ASTM C1628.\n\nIn the particular case of the elastomeric joint for nonreinforced concrete pipe, it must comply with standard ASTM C443.\n\nIt is not permitted to mortar (solaquear) the bells manufactured for pipe-to-pipe union with an elastomeric joint.\n\n4.2.3.\nSynthetic and non-synthetic fibers\n\nIt is permitted to include fibers in the mix for concrete pipe with or without reinforcement, provided they are type II or III if \"synthetic\", or type I if \"non-synthetic\", in accordance with the requirements indicated in the pipe manufacturing standard, be it ASTM C14M or ASTM C76M as applicable.\n\nIn all cases, the fibers must comply with the requirements of standard INTE C31 (INTE 06-01-20), as a non-structural manufacturing material.\n\nWhen the pipe incorporates synthetic or non-synthetic fibers that comply with the indicated requirements, a certification issued by the pipe manufacturer must be provided, indicating for each type of fiber, the following:\n\n. Type, name, and composition of the fiber.\n\n. Name and code of the manufacturing standard for each type of fiber.\n\n. Method of adding the fiber to the concrete.\n\n. Explanatory detail of the contribution to the expected functioning or performance of the pipe, by incorporating the fiber as a non-structural material.\n\n4.2.4.\nColor\n\nThe color of the pipe must comply with that established for storm systems, in accordance with the \"Technical standard for the design and construction of potable water supply, sanitation, and storm systems\" of AyA.\n\nTherefore, any reference or color requirement included in the product technical standards referenced directly or indirectly in this specification is rendered null and void.\n\n4.2.5.\nLabeling\n\nEach pipe must comply with the labeling requirement established in the respective manufacturing technical standard (product technical standard), whose characters must be totally visible, legible, and indelible, to guarantee the correct identification of the pipe during and after installation.\n\n5.\nComplementary provisions\n\n5.1.\nProduct certifications\n\nThe product certification requirement issued by a Conformity Assessment Body (Organismo Evaluador de la Conformidad, OEC), a third-party body, applies under the terms established in the \"Technical standard for the design and construction of potable water supply, sanitation, and storm systems\" of AyA.\n\nIn the technical offer, the product certification of the pipe regarding the manufacturing standard with which it complies must be provided, with only ASTM C14M or ASTM C76M being acceptable, as applicable.\n\n5.2.\nHandling, storage, and transportation\n\nIn the technical offer, a chapter on \"Handling, storage, and transportation\" must be incorporated, detailing the actions and recommendations from the manufacturer(s) for the adequate handling, transportation, and storage of the pipes; the foregoing, as required prior to or during the construction process, in order to guarantee their functionality and useful life.\n\nLikewise, any provision indicated for such purposes in the manufacturing technical standards applicable to the pipe must be included in this chapter.\n\n6.\nReferenced normative documents\n\nThe standards cited in this section form an integral part of the technical requirements included in this document. The editions indicated were in force at the time of formulating this specification:\n\nAyA Board of Directors Agreement No. 2017-281 \"Technical standard for the design and construction of potable water supply, sanitation, and storm systems\". Published in ALCANCE No. 227 A,B,C,D,E,F,G of La Gaceta No. 180 of September 22, 2017\n\nASTM C14M-2020 \"Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric)\"\n\nASTM C1628-2019 \"Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe, Using Rubber Gaskets\"\n\nASTM C443-2020 \"Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets\"\n\nASTM C76M-2020 \"Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)\" ASTM C990-09 (reapproved 2019)\n\n\"Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants\"\n\nINTE C31:2016 \"Concrete reinforcing fiber. Specifications\"\n\nIn the event that a standard is updated by the issuer after the delivery of the technical offer or during the supply or installation process, the contracting party and the contractor must review whether the requirements contained in the standard maintain their application, within the scope of this technical specification.\n\nThe codes of the national standards indicated in parentheses that contain the code \"INTE\" correspond to the codification previously established by the Instituto de Normas Técnicas de Costa Rica (INTECO).\n\n7. Annexes (normative and informative)\n\nThis document does not contain normative or informative annexes.\n\n8.\nBibliography\n\nThe requirements integrated into this technical specification are based on technical criteria according to areas of competence and on referenced normative documents.\n\n9.\nDescriptors\n\nConcrete; pipe and accessories.\n\n10. Version control"
}