{
  "id": "norm-54734",
  "citation": "Decreto 32327",
  "section": "norms",
  "doc_type": "executive_decree",
  "title_es": "Reglamento para la Calidad del Agua Potable",
  "title_en": "Drinking Water Quality Regulation",
  "summary_es": "Este decreto ejecutivo establece los niveles máximos admisibles de componentes físicos, químicos, biológicos y microbiológicos que debe cumplir el agua potable suministrada por entes operadores públicos y privados en Costa Rica, con el fin de proteger la salud pública. Define cuatro niveles progresivos de control de calidad (N1 a N4) según el tamaño de la población abastecida y el riesgo sanitario, desde parámetros básicos organolépticos y bacteriológicos hasta análisis avanzados de sustancias tóxicas, plaguicidas y subproductos de desinfección. Asigna al Ministerio de Salud la vigilancia sanitaria y a los operadores la responsabilidad de ejecutar los programas de control, muestreo y acciones correctivas cuando se excedan los valores máximos. Incluye disposiciones sobre desinfección con cloro u ozono, puntos de muestreo, frecuencia de análisis, y obligación de informar al Ministerio. Fue derogado en 2015 por el Decreto Ejecutivo N° 38924.",
  "summary_en": "This executive decree sets the maximum admissible levels for physical, chemical, biological, and microbiological components that drinking water supplied by public and private operators in Costa Rica must meet, in order to protect public health. It defines four progressive control levels (N1 through N4) based on the population served and sanitary risk, ranging from basic organoleptic and bacteriological parameters to advanced analysis of toxic substances, pesticides, and disinfection byproducts. It assigns sanitary surveillance to the Ministry of Health and makes operators responsible for implementing control programs, sampling, and corrective actions when maximum values are exceeded. It includes provisions on disinfection with chlorine or ozone, sampling points, frequency of analysis, and the obligation to report to the Ministry. It was repealed in 2015 by Executive Decree No. 38924.",
  "court_or_agency": "",
  "date": "10/02/2005",
  "year": "2005",
  "topic_ids": [
    "_off-topic"
  ],
  "primary_topic_id": null,
  "es_concept_hints": [
    "agua potable",
    "valor máximo admisible",
    "ente operador",
    "desinfección con cloro",
    "control de calidad N1 al N4",
    "vigilancia sanitaria",
    "coliformes fecales",
    "subproductos de la desinfección"
  ],
  "concept_anchors": [
    {
      "article": "Arts. 264-267 y concordantes",
      "law": "Ley Nº 5395"
    }
  ],
  "keywords_es": [
    "calidad del agua potable",
    "reglamento",
    "Decreto 32327",
    "Ministerio de Salud",
    "desinfección",
    "control de calidad",
    "parámetros microbiológicos",
    "valor máximo admisible",
    "agua para consumo humano",
    "ente operador",
    "acueducto",
    "Anexo 1",
    "Anexo 2",
    "derogado"
  ],
  "keywords_en": [
    "drinking water quality",
    "regulation",
    "Decree 32327",
    "Ministry of Health",
    "disinfection",
    "quality control",
    "microbiological parameters",
    "maximum admissible value",
    "water for human consumption",
    "operator",
    "aqueduct",
    "Annex 1",
    "Annex 2",
    "repealed"
  ],
  "excerpt_es": "Artículo 1º-Objetivo y Alcances. El presente reglamento tiene por objetivo establecer los niveles máximos que deben tener aquellos componentes o características del agua que pueden representar un riesgo para la salud de la comunidad e inconvenientes para la preservación de los sistemas de abastecimiento de agua en beneficio de la salud pública.\n\nArtículo 5º-Para todos los efectos de regulaciones en la calidad del agua potable abastecida, los organismos operadores se sujetarán a este reglamento que contiene los valores para los parámetros físicos, químicos, biológicos y microbiológicos en sus aspectos estéticos, organolépticos y de significado para la salud establecidos en los cuadros 1, 2, 3, 4, 5, 6 y 7 del anexo 1.\n\nArtículo 9º-Cuando se sobrepase el valor máximo admisible es necesario que el ente operador proceda a:\n9.1 Efectuar una inspección sanitaria con remuestreo, para identificar las causas del cambio de calidad y ejecutar las acciones correctivas.\n9.2 Consultar a las autoridades nacionales responsables: Ministerio de Salud, A y A, para que proporcionen asesoramiento sobre el grado de riesgo y la prioridad de las acciones correctivas.\n9.3 Las entidades públicas y privadas que funjan como operadores, de acuerdo con el grado de riesgo, deben presentar ante el Ministerio de Salud, el informe de acciones correctivas ejecutadas y un plan de actividades para evitar que el evento no vuelva a ocurrir.",
  "excerpt_en": "Article 1 – Objective and Scope. This regulation aims to establish the maximum levels that those components or characteristics of water that may pose a risk to community health and inconveniences for the preservation of water supply systems must have, for the benefit of public health.\n\nArticle 5 – For all regulatory purposes regarding the quality of supplied drinking water, operating entities shall adhere to this regulation, which contains the values for physical, chemical, biological, and microbiological parameters in their aesthetic, organoleptic, and health-significant aspects set forth in Tables 1, 2, 3, 4, 5, 6, and 7 of Annex 1.\n\nArticle 9 – When the maximum admissible value is exceeded, the operating entity must:\n9.1 Conduct a sanitary inspection with resampling to identify the causes of the quality change and implement corrective actions.\n9.2 Consult the responsible national authorities: Ministry of Health, AyA, to obtain advice on the degree of risk and the priority of corrective actions.\n9.3 Public and private entities acting as operators, according to the degree of risk, must submit to the Ministry of Health a report of the corrective actions taken and an activity plan to prevent the event from recurring.",
  "outcome": {
    "label_en": "Repealed",
    "label_es": "Derogada",
    "summary_en": "The Drinking Water Quality Regulation, Executive Decree No. 32327, was repealed by Article 20 of the Drinking Water Quality Regulation, Decree No. 38924 of January 12, 2015.",
    "summary_es": "El Reglamento para la Calidad del Agua Potable, Decreto Ejecutivo N° 32327, fue derogado por el artículo 20 del Reglamento para la calidad del Agua Potable, Decreto N° 38924 del 12 de enero de 2015."
  },
  "pull_quotes": [
    {
      "context": "Artículo 1",
      "quote_en": "This regulation aims to establish the maximum levels that those components or characteristics of water that may pose a risk to community health and inconveniences for the preservation of water supply systems must have, for the benefit of public health.",
      "quote_es": "El presente reglamento tiene por objetivo establecer los niveles máximos que deben tener aquellos componentes o características del agua que pueden representar un riesgo para la salud de la comunidad e inconvenientes para la preservación de los sistemas de abastecimiento de agua en beneficio de la salud pública."
    },
    {
      "context": "Artículo 5",
      "quote_en": "Operating entities shall adhere to this regulation, which contains the values for physical, chemical, biological, and microbiological parameters in their aesthetic, organoleptic, and health-significant aspects set forth in Tables 1, 2, 3, 4, 5, 6, and 7 of Annex 1.",
      "quote_es": "Los organismos operadores se sujetarán a este reglamento que contiene los valores para los parámetros físicos, químicos, biológicos y microbiológicos en sus aspectos estéticos, organolépticos y de significado para la salud establecidos en los cuadros 1, 2, 3, 4, 5, 6 y 7 del anexo 1."
    },
    {
      "context": "Artículo 12",
      "quote_en": "Disinfection must also be applied to maintain a residual level, as indicated in Article 13, that guarantees the quality of the water against eventual contaminations throughout the distribution system.",
      "quote_es": "La desinfección deberá aplicarse además para mantener un nivel residual, según lo indicado en el artículo 13, que garantice la calidad del agua de contaminaciones eventuales a través de todo el sistema de distribución."
    }
  ],
  "cites": [],
  "cited_by": [],
  "references": {
    "internal": [
      {
        "target_id": "norm-6581",
        "kind": "concept_anchor",
        "label": "Ley Nº 5395  Arts. 264-267 y concordantes"
      }
    ],
    "external": []
  },
  "source_url": "https://pgrweb.go.cr/scij/Busqueda/Normativa/Normas/nrm_texto_completo.aspx?param1=NRTC&nValor1=1&nValor2=54734&strTipM=TC&nValor3=0",
  "tier": 2,
  "_editorial_citation_count": 0,
  "regulations_by_article": null,
  "amendments_by_article": null,
  "dictamen_by_article": null,
  "concordancias_by_article": null,
  "afectaciones_by_article": null,
  "resoluciones_by_article": null,
  "cited_by_votos": [],
  "cited_norms": [],
  "cited_norms_inverted": [],
  "sentencias_relacionadas": [],
  "temas_y_subtemas": [],
  "cascade_only": false,
  "amendment_count": 0,
  "body_es_text": "en la totalidad del texto\n\n                    -\n\n                        Texto Completo Norma 32327\n\n                        Reglamento para la Calidad del Agua Potable\n\nTexto Completo acta: 106099\nNº 32327\n\nNº 32327\n\n(Este decreto ejecutivo fue\nderogado por el artículo 20 del Reglamento para la calidad del Agua Potable,\naprobado mediante decreto ejecutivo N° 38924 del 12 de enero del  2015)\n\nEL PRESIDENTE DE LA REPÚBLICA\n\nY LA MINISTRA DE SALUD\n\n \n\nEn ejercicio de las facultades que les confieren los\nartículos 140 incisos 3), 18) y 146) de la Constitución Política; 28 inciso b)\nde la Ley General de Administración Pública; 1, 2, 4, 7, 264, 265, 266, 267 y\nsiguientes y concordantes de la Ley General de Salud (Ley Nº 5395 del 30 de\noctubre de 1973).\n\n \n\nConsiderando:\n\n \n\nI.-Que es deber del Estado, a través de sus\ninstituciones, de velar por la salud pública.\n\nII.-Que por tal razón se hace necesario y oportuno,\ndictar las normas relacionadas con la calidad del agua de consumo humano.\n\nIII.-Que las entidades públicas y privadas, que\nfunjan como operadores de acueductos de agua potable, deberán sujetarse a lo\nestablecido en el presente reglamento a fin de garantizar la calidad del agua.\n\nIV.-Que el Ministerio de Salud, al tener como misión\nvelar por la salud pública, debe regular vía reglamento, la calidad del agua y\nasí prevenir enfermedades en los seres humanos originadas por contaminación del\nagua. Por tanto:\n\nDECRETAN:\n\nReglamento\npara la Calidad del Agua Potable\n\n \n\nCAPÍTULO I\n\nDe las\ndisposiciones generales y definiciones\n\nArtículo 1º-Objetivo\ny Alcances. El presente reglamento tiene por objetivo establecer los\nniveles máximos que deben tener aquellos componentes o características del agua\nque pueden representar un riesgo para la salud de la comunidad e inconvenientes\npara la preservación de los sistemas de abastecimiento de agua en beneficio de\nla salud pública.\n\nArtículo 2º-Definiciones\ny Unidades. Para una mejor comprensión del presente reglamento, se\nestablecen las siguientes definiciones y tabla de unidades:\n\n \n\na) Acreditación:\nProcedimiento por el cual un ente autorizado otorga reconocimiento formal de\nque un organismo o persona es competente para llevar a cabo tareas específicas.\n\nb) Agua potable: Agua tratada que cumple con las disposiciones de\nvalores recomendables o máximos admisibles estéticos, organolépticos, físicos,\nquímicos, biológicos y microbiológicos, establecidos en el presente reglamento\ny que al ser consumida por la población no causa daño a la salud.\n\nc) Agua superficial: La que se origina a partir de precipitaciones\natmosféricas, afloración de aguas subterráneas (ríos, manantiales, lagos,\nquebradas). \n\nd) Agua\nsubterránea: La que se origina de la infiltración a través de formaciones\nde una o más capas subterráneas de rocas o de otros estratos geológicos que\ntienen la suficiente permeabilidad para permitir un flujo significativo\naprovechable sosteniblemente para su extracción. \n\ne) Agua tratada:\nAgua subterránea o superficial cuya calidad ha sido modificada por medio de\nprocesos de tratamiento que incluyen como mínimo a la desinfección en el caso\nde aguas de origen subterráneo. Su calidad debe ajustarse a lo establecido en\nel presente reglamento.\n\nf) Control de\ncalidad del agua potable: evaluación continua y sistemática de la calidad\ndel agua desde la fuente, planta de tratamiento, sistemas de almacenamiento y\ndistribución, según programas específicos que deben ejecutar los organismos\noperadores a fin de cumplir las normas de calidad. \n\ng) Desinfección\ndel agua: corresponde a un proceso físico químico unitario cuyo objetivo es\ngarantizar la inactivación o destrucción de los agentes patógenos en el agua a\nutilizar para consumo humano.  El proceso\nquímico de la desinfección no corresponde a una esterilización. \n\nh) Inspección\nsanitaria: corresponde a las visitas, como componente de la vigilancia de\nla calidad del agua potable, para la aplicación de fichas de campo que permitan\nrevisar el estado de las diferentes estructuras (captaciones, almacenamiento,\ndistribución) de un sistema de suministro de agua para consumo humano y de las\náreas de influencia a las captaciones, para identificar los riesgos que pueden\nafectar su calidad.\n\ni) Muestra de agua: Es una porción de agua que se recolecta de tal\nmanera que resulte representativa de un volumen mayor de líquido.\n\nj) OPS / OMS: Organización Panamericana de la Salud / Organización\nMundial de la Salud. \n\nk) Entes\noperadores: instituciones, empresas, asociaciones administradoras o\nentidades en general públicas o privadas, directamente encargadas de la\noperación, mantenimiento y administración de sistemas de suministro de agua\npotable. \n\nl) Redesinfección\ndel agua: aplicación de un desinfectante al agua en uno o varios puntos del\nsistema de distribución tales como: red, almacenamiento y estación de bombeo\ndespués de un tratamiento previo con el desinfectante para cumplir con los\nvalores establecidos en el en el cuadro del artículo 12 del capítulo V. \n\nm) Valor\nmáximo admisible: corresponde a aquella concentración de sustancia o\ndensidad de bacterias a partir de la cual existe rechazo del agua por parte de\nlos consumidores o surge un riesgo inaceptable para la salud. El sobrepasar\nestos valores indicados en las tablas contenidas en el Anexo 1 implica la toma\nde acciones correctivas inmediatas. \n\nn) Valor\nrecomendado: corresponde a aquella concentración de sustancia o densidad de\nbacterias que implica un riesgo mínimo o aceptable para la salud de los\nconsumidores del agua potable.\n\nñ) Vigilancia\nde la calidad del agua potable: es la evaluación permanente desde el punto\nde vista de salud pública, efectuada por el Ministerio de Salud, sobre los\norganismos operadores, a fin de garantizar la seguridad, inocuidad y aceptabilidad\ndel suministro de agua potable desde el área de influencia de la fuente hasta\nel sistema de distribución.\n\n \n\n \n\n| mg/L | Miligramos por litro | | --- | --- | | ppm | Partes por millón | | µg/L | Microgramos por\nlitro | | µS/cm | Micro siemens por centímetros | | PH | Potencial de iones hidrógeno | | U Pt-Co |\nUnidades de platino cobalto (para Color) | | UNT | Unidades Nefelométricas de Turbiedad | | °C |\nGrados Celsius | | NMP/100mL | Número más Probable de bacterias en 100 mililitros de agua, por el\nmétodo de tubo múltiples de fermentación | | UFC/100mL | Unidades formadoras de colonias en 100\nmililitros de agua, por el método de membrana filtrante | | UFC/ mL | Unidades formadoras de\ncolonias en un mililitro de agua |\n\nArtículo 3º-Para efectos del ámbito de aplicación de\neste reglamento, se establece que el nivel de vigilancia de la calidad del agua\npotable, corresponde al Ministerio de Salud y los niveles de administración, control\ny ejecución a los organismos operadores. \n\nArtículo 4º-En este reglamento se establecen los\nrequisitos básicos que debe contener el agua potable que suministran los entes\noperadores.\n\nCAPÍTULO II\n\nDel ámbito de aplicación\n\n \n\nArtículo 5º-Para todos los efectos de regulaciones en\nla calidad del agua potable abastecida, los organismos operadores se sujetarán\na este reglamento que contiene los valores para los parámetros físicos,\nquímicos, biológicos y microbiológicos en sus aspectos estéticos,\norganolépticos y de significado para la salud establecidos en los cuadros 1, 2,\n3, 4, 5, 6 y 7 del anexo 1.\n\nArtículo 6º-En este reglamento se establecen cuatro\nniveles de Control de Calidad del Agua (ver Anexo 2 cuadro A):\n\n \n\n6.1 Nivel Primero (N1): corresponde al programa de\ncontrol básico junto con la inspección sanitaria, para evaluar la operación y\nmantenimiento en la fuente, el almacenamiento y la distribución del agua\npotable. Los parámetros en este nivel son: coliformes termotolerantes\n(fecales), Escherichia coli, color aparente, turbiedad, olor, sabor,\ntemperatura, pH, conductividad, y cloro residual libre o combinado. Los valores\nrecomendados y máximos admisibles se indica en el cuadro1 del anexo 1. Si la\ninspección sanitaria establece otros riesgos de contaminación, deberán\nadicionarse al programa de control básico, los parámetros necesarios.\n\n6.2 Nivel Segundo (N2): corresponde al programa de\ncontrol básico ampliado (N1), el análisis de tendencias temporales de\nvariaciones de calidad en las fuentes de abastecimiento, a ser aplicado en\nmuestras de agua potable en la fuente, su almacenamiento y distribución. Los\nparámetros en esta etapa de control son todos los establecidos en el nivel N1,\nampliados con: dureza total, cloruro, fluoruro, nitrato, sulfato, aluminio,\ncalcio, magnesio, sodio, potasio, hierro, manganeso, zinc, cobre, plomo. Los\nvalores recomendados y admisibles se indican en el cuadro 2 del anexo 1.\n\n6.3 Nivel Tercero (N3): corresponde al programa de\ncontrol avanzado del agua potable. Comprende la ejecución de los parámetros del\nnivel N2 ampliados con: nitrito, amonio, arsénico, cadmio, cromo, mercurio,\nníquel, antimonio, selenio y residuos de plaguicidas.  Los valores recomendados y máximos admisibles\nse indican en los cuadros 3 y 4 del anexo 1.\n\n6.4 Nivel Cuarto (N4): corresponde a programas\nocasionales ejecutados por situaciones especiales, de emergencia o porque la\ninspección sanitaria identifica un riesgo inminente de contaminación del agua.\nLos parámetros a analizar según sea la situación identificada pueden ser:\nsólidos totales disueltos, sulfuro de hidrógeno, cianuros, sustancias orgánicas\nde significado para la salud, desinfectantes y subproductos de la desinfección.\nLos valores recomendados y máximos admisibles se indican en los cuadros 5, 6 y\n7 del anexo 1. Otros parámetros como: Siguella sp, Salmonella sp.,\nEstreptococos fecales, Vibrio cholerae 01 toxigénico,Aeromonas hydrophila, nemátodos,\nEntamoeba hystolytica, Cryptosporidium, Virus de Hepatitis A,. Enterovirus y\ncianobacterias tóxicas, deben estar ausentes en las muestras analizadas. Como\nindicadores e vulnerabilidad de un sistema pueden utilizarse los coliformes\ntotales.\n\n \n\n \n\nEl Ministerio de Salud o el ente operador, podrán\nampliar los parámetros de control requeridos para cada situación. El ente\noperador enviará los resultados del control de calidad del agua potable al\nMinisterio de Salud.\n\nArtículo 7º-Las entidades públicas y privadas que\nfungen como operadores de servicios públicos, deben tomar las acciones\nrequeridas para que se cumpla:\n\n \n\n7.1 El programa de control hasta el nivel primero en\ntodos los acueductos del país\n\n7.2 El programa de control hasta nivel segundo en\ntodos los acueductos con población abastecida superior a 10.000 habitantes\n\n7.3 El programa de control hasta el nivel tercero en\ntodos los acueductos con población abastecida superior a 50.000 habitantes\n\nArtículo 8º-De los Métodos de Análisis y\nLaboratorios.\n\n \n\n8.1 Preferiblemente los métodos de referencia para\nanálisis son los indicados en la última edición de los Standard Methods for the\nExamination of Water and Wastewater y los métodos de ensayos acreditados\nconforme lo establece la ley Nº 8279 de 2 de mayo del 2002, (Sistema Nacional\npara la Calidad) Publicado en el Diario Oficial La Gaceta Nº 96 de 21 de mayo\ndel 2002.\n\n8.1 Los laboratorios que realicen análisis de agua\ncontemplados en este reglamento deberán tener permiso de funcionamiento\notorgado por el Ministerio de Salud según Decreto 30465-S. (Reglamento General\npara el Otorgamiento de Permisos de Funcionamiento por parte del Ministerio de\nSalud) del nueve de mayo del dos mil dos, publicado en el Diario Oficial La\nGaceta Nº 102 del día 29 de mayo del dos mil dos.\n\nArtículo 9º-Cuando se sobrepase el valor máximo\nadmisible es necesario que el ente operador proceda a:\n\n \n\n9.1 Efectuar una inspección sanitaria con remuestreo,\npara identificar las causas del cambio de calidad y ejecutar las acciones\ncorrectivas.\n\n9.2 Consultar a las autoridades nacionales\nresponsables: Ministerio de\n\nSalud, A y A, para que proporcionen asesoramiento\nsobre el grado de riesgo y la prioridad de las acciones correctivas.\n\n9.3 Las entidades públicas y privadas que funjan como\noperadores, de acuerdo con el grado de riesgo, deben presentar ante el\nMinisterio de Salud, el informe de acciones correctivas ejecutadas y un plan de\nactividades para evitar que el evento no vuelva a ocurrir.\n\nCAPÍTULO III\n\nDel programa de control de\ncalidad\n\n \n\nArtículo 10.-Para implementar el Programa de Control\nde Calidad del Agua, el ente operador debe cumplir como mínimo con:\n\n \n\n10.1 Identificar la zona de abastecimiento.\n\n \n\n10.1a La zona de abastecimiento corresponde al área\ngeográfica del sistema, de características homogéneas en relación con la fuente\ny sus componentes relacionados: almacenamiento y sector de la red de\ndistribución.\n\n10.1b En sistemas con más de una fuente, la\nrecolección de muestras debe ser realizada teniendo en cuenta el número de\nhabitantes abastecido con cada fuente.\n\n \n\n10.2 Puntos de recolección de muestras.\n\n \n\n10.2a Los puntos de recolección de muestras deben ser seleccionados de modo que sean representativos\nde las zonas de abastecimiento; iniciando con la fuente, almacenamiento y terminando en la red de\ndistribución. El grifo de muestreo debe estar ubicado lo más próximo a la conexión domiciliaria\ncontrolada por el operador, libre de la influencia de la cisterna, tanque elevado o cualquier otro\ntipo de almacenamiento intradomiciliar de agua.  10.2b Deben ser uniformemente distribuidos en cada\nzona de abastecimiento.\n\n10.2c El número de muestras bacteriológicas y\nfísico-químicas, en la red de distribución, debe ser proporcional al número de\nhabitantes atendidos en cada zona de abastecimiento.  10.2d Deben ser ubicados: a la salida de la\nplanta de tratamiento, salida de tanques de almacenamiento, salida de las\nfuentes subterráneas (pozos, manantiales, galerías de infiltración, etc.), en\nla red primaria y secundaria de distribución.\n\n \n\n10.3 Frecuencia de recolección de muestras Con la\nfinalidad de asegurar que el agua de abastecimiento satisface los requisitos de\neste Reglamento, es necesario recolectar las muestras con la periodicidad que\nestablece el cuadro B del anexo 2.\n\n \n\n10.4 Programa de control de riesgo y vulnerabilidad. \n\n \n\n10.4a Realizar la inspección sanitaria, a cada uno de\nlos elementos del acueducto, una vez al año, durante una recolección de\nmuestras del programa de control de calidad. \n\n10.4b Evaluar los resultados de la inspección\nsanitaria, en conjunto con el último año de datos de análisis, obtenidos en el\nprograma de control de calidad.\n\n10.4c Definir el grado de riesgo para la salud, en\ncada uno de los elementos del sistema, así como la priorización de acciones\ncorrectivas.\n\nCAPÍTULO IV\n\nDel programa de vigilancia\nsanitaria de la calidad del agua\n\n \n\nArtículo 11.-Corresponde al Ministerio de Salud, a\ntravés de los diferentes niveles de gestión, efectuar la evaluación del ente\noperador, desde el punto de vista operativo y su capacidad para implementar\nmejoras, con el fin de disminuir el grado de riesgo, para la salud de la\npoblación '79 la vulnerabilidad de los sistemas.\n\nCAPÍTULO V\n\nDesinfección\n\n \n\nArtículo 12.-Utilización\nde la desinfección. El proceso de desinfección se utiliza como parte de una\nserie de operaciones y procesos de tratamiento unitario en una planta. En su\nforma mas simple se aplica como único tratamiento de aguas naturales de\nexcelente calidad (aguas subterráneas o de manantial) para garantizar ausencia\nde indicadores de contaminación fecal entre el punto de aplicación y el punto\nde entrega al usuario. La desinfección deberá aplicarse además para mantener un\nnivel residual, según lo indicado en el artículo 13, que garantice la calidad\ndel agua de contaminaciones eventuales a través de todo el sistema de\ndistribución.\n\nArtículo 13.-Dosis\nde desinfectante. La dosis de desinfectante corresponde a la cantidad en\npartes por millón (mg/L) que se aplica al agua. La dosis que debe aplicarse\nvaría con la demanda de cada agua en particular.\n\n \n\n13.1 Desinfección con cloro\n\n \n\nEs función del tipo de residual que se tenga. Se\nrecomienda, para la destrucción de bacterias indicadoras el mínimo de cloro, en\nla red de distribución, dependiendo del pH del agua y tiempo mínimo de contacto\ndado en el siguiente cuadro.\n\n \n\n| Valor del pH | Cloro residual libre (mg/L) Tiempo mínimo de Contacto de 20 minutos | Cloro\nresidual combinado (mg/L) Tiempo mínimo de Contacto de 60 minutos | | --- | --- | --- | | 6.0 - 7.0\n| 0.3 | 1.0 | | 7.1 - 8.0 | 0.5 | 1.5 | | 8.1 - 9.0 | 0.6 | 1.8 |\n\n \n\n \n\n13.2         \nDesinfección\ncon ozono\n\n \n\nPara desinfectar un metro cúbico de agua se utiliza\nen la práctica, de 0.5 a 2 gramos de ozono, dependiendo de la calidad del agua\ntratada. El residual en el punto de aplicación debe ser de 0.3 a 0.4 mg/L,\ndurante 3 a 4 minutos de tiempo de contacto mínimo.\n\nArtículo 14.-Puntos\nde dosificación\n\n \n\n14.1 Los puntos de adición de los desinfectantes son\na la salida de los procesos de tratamiento de las plantas, asegurándose que\nexista el periodo de contacto adecuado antes de que el agua entre al sistema de\ndistribución.\n\n14.2 Puntos de redesinfección: Estos puntos de\naplicación pueden ser:\n\n14.2a Al final de una línea larga de alimentación\ndentro del sistema de distribución.\n\n14.2b En un punto donde una tubería principal deriva\nagua hacia otra comunidad próxima.\n\n14.2c En un punto del sistema donde exista una\nestación de bombeo, en el tanque de almacenamiento.\n\nCAPÍTULO VI\n\nDe las disposiciones finales\n\n \n\nArtículo 15.-Todo ente operador, de sistemas de\nabastecimiento de agua, está obligado a entregar copia de los informes de su\nprograma de Control de la Calidad del Agua al Ministerio de Salud.\n\nArtículo 16.-En caso de emergencia calificada como\ntal por las autoridades sanitarias de acuerdo con el presente reglamento, el\nente operador debe:\n\n \n\n16.1 Suspender el servicio de abastecimiento.\n\n16.2 Asegurar el suministro de agua por otra vía.\n\n16.3 Aplicar las acciones correctivas\ncorrespondientes.\n\n16.4 Entrar a operar el sistema, una vez asegurada la\ncalidad del agua.\n\nArtículo 17.-No se debe introducir agua superficial,\nsin tratamiento respectivo, en los sistemas de abastecimiento de agua potable.\nEl ente operador debe asegurar la calidad sanitaria del agua dentro del sistema\nde almacenamiento y distribución, durante todo el año. \n\nArtículo 18.-Los Anexos 1 y 2 a que se hace alusión\nen artículos anteriores forman parte integral del presente reglamento.\n\nArtículo 19.-Este reglamento entrará en vigencia ocho\ndías después de la fecha de su publicación en el Diario Oficial La Gaceta. \n\nArtículo 20.-El presente Decreto deroga el Decreto\nEjecutivo Nº 25991-S, del 14 de abril de 1997, publicado en La Gaceta el 27 de\nmayo de 1997.\n\n \n\nDado en la Presidencia de la República.-San José, a\nlos diez días del mes de febrero del dos mil cinco.\n\nANEXO 1\n\n \n\nCUADRO 1. PARÁMETROS DE CALIDAD\nDEL AGUA\n\n-         \nPRIMER NIVEL DE CONTROL - N1\n\n \n\n| Parámetro | Unidad | Valor Recomendado | Valor Máximo Admisible |\n| --- | --- | --- | --- |\n| Coliforme fecal | NMP/100 mL o UFC/100 mL | Ausente | Ausente |\n| Escherichia coliª | NMP/100 mL o UFC/100 mL | Ausente | Ausente |\n| Color aparente | mg/L (U - Pt-Co) | 5 | 15 b |\n| Turbiedad | UNT | <1 | 5 b |\n| Olor | - | Debe ser aceptable | Debe ser aceptable |\n| Sabor | - | Debe ser aceptable | Debe ser aceptable |\n| Temperatura | ºC | 18 | 30 |\n| pHc | Valor pH | 6,5 | 8,5 |\n| Conductividad | µS/cm | 400 |  |\n| Cloro Residual Libre | mg/L | 0,3 | 0,6 |\n| Cloro Residual | mg/L | 1,0 | 1,8 |\n| Combinado |  |  |  |\n\n \n\nCUADRO 2. PARÁMETROS DE CALIDAD\nDEL AGUA\n\n-         \nSEGUNDO NIVEL DE CONTROL - N2\n\n \n\n| Parámetro | Unidad | Valor Recomendado | Valor Máximo Admisible |\n| --- | --- | --- | --- |\n| Dureza Total | mg/L CaCO3 | 400 | 500 |\n| Cloruro | mg/L Cl- | 25 | 250 |\n| Fluoruro | mg/L F- |  | 0,7 a 1,5 a |\n| Nitrato | mg/L N0 3 | 25 | 50 |\n| Sulfato | mg/L S04 2 | 25 | 250 |\n| Aluminio | mg/L Al+3 | 0,2 |  |\n| Calcio | mg/L Ca+2 | 100 |  |\n| Magnesio | mg/L Mg+2 | 30 | 50 |\n| Sodio | mg/L Na+ | 25 | 200 |\n| Potasio | mg/L K+ |  | 10 |\n| Hierro | mg/L Fe |  | 0,3 |\n\n \n\na El\nindicador bacteriológico más preciso de contaminación fecal es la Escherichia\ncoli.\n\n b VMA en no más del 10% de las muestras\nanalizadas durante el año.\n\n c Las aguas deben ser estabilizadas de manera\nque no produzcan efectos corrosivos ni incrustantes en los acueductos o en los\nutensilios domésticos, utilizados para calentar o hervir el agua.\n\n \n\n \n\n| Parámetro | Unidad | Valor Recomendado | Valor Máximo Admisible |\n| --- | --- | --- | --- |\n| Manganeso | mg/L Mn | 0,1 | 0,5 |\n| Zinc | mg/L Zn |  | 3,0 |\n| Cobre | mg/L Cu | 1,0 | 2,0 |\n| Plomo | mg/L Pb |  | 0,01 |\n\n \n\n \n\na 1,5\nmg/L para temperaturas de 8 a 12 ºC y 0,7 mg/L para temperaturas de 25 a 30 ºC\n\n \n\n \n\nCUADRO 3. PARÁMETROS DE CALIDAD\nDEL AGUA\n\n-TERCER NIVEL DE CONTROL- N3\n\n \n\n| Parámetro | Unidad | Valor Recomendado | Valor Máximo Admisible |\n| --- | --- | --- | --- |\n| Nitrito | mg/L NO2 |  | 0,1 o 3,0 a |\n| Amonio | mg/L NH4 | 0,05 | 0,5 |\n| Arsénico | mg/L As |  | 0,01 |\n| Cadmio | mg/L Cd |  | 0,003 |\n| Cromo | mg/L Cr |  | 0,05 |\n| Mercurio | mg/L Hg |  | 0,001 |\n| Níquel | mg/L Ni |  | 0,02 |\n| Antimonio | mg/L Sb |  | 0,005 |\n| Selenio | mg/L Se |  | 0,01 |\n\n \n\n \n\na __ VMA de 0.1, si el nitrito se evalúa en forma\nindependiente del nitrato.\n\n___ VMA de 3.0, cuando el nitrito se evalúa en\nconjunto con el nitrato. En este caso, la suma de la razón de concentración de\ncada uno respecto a su valor máximo admisible no debe ser superior a 1,0.\n\n \n\nVer\nformula en La gaceta impresa N° 84 del 3 de mayo del 2005.\n\n \n\nNota: V.M.A. = Valor Máximo Admisible.\n\n \n\n \n\nCUADRO 4. PARÁMETROS DE CALIDAD\nPARA RESIDUOS\n\nDE PLAGUICIDAS\n\nTERCER NIVEL DE CONTROL- N3\n\n \n\n| Parámetro Ingrediente activo ISO, BSI, ANSI | Nombre Químico IUPAC | Valor Máximo Admisible µg/L |\n| --- | --- | --- | | Alachlor | 2-cloro-2,6-dietil (metoximetil)acetanilida | 20 | | Aldicarb |\n2-metil-2-(metiltio)propionaldehído-O- (metilcarbamoil) oxima. | 10 | | Aldrin/dieldrin |\n(1R,4S,4aS,5S,8R,8aR)-1,2,34,10,10- hexacloro-1,4,4a,5,8,8a-hexahidro-1,4:5,8 - dimetanonaftaleno |\n. 0,03 | | Atrazine | 6-cloro-N2-etil-N4-isopropil-1,3,5-triazina-2,4- diamina | 2 | | Bentazone |\n3-isopropil-1H-2,1,3-benzotiadiazin-4(3H)- ona-2,2-dióxido. | 300 | | Carbofuran |\n2,3-dihidro-2,2-dimetil-7-benzofuranil-metilcarbamato. | 7 | | Chlordane |\n1,2,4,5,6,7,8,8-octacloro-2,3,3ª,4,7,7ahexahidro- 4,7-metanoindeno | . 0,2 | | 2,4-D |\nÁcido-2,4-diclorofenoxiacético. | 30 | | 2,4-DB | Ácido-4-(2,4-diclorofenoxi)butírico. | 90 | | DDTa\n| Dicloro-difenil-tricloroetano | . 2 | | Dibromocloropropano | 1,2-dibromo-3-cloropropano. | . 1 |\n| Dichloropropene | 1,3-dicloropropeno | . 20 | | Dichlorprop | Ácido\n(RS)-2-(2,4-diclorofenoxi)propiónico | 100 | | Heptachlor + epoxide |\n1,4,5,6,7,8,8-heptacloro-3a,4,7,7a-tetrahidro- 4,7-metanoindeno | . 0,03 | | Isoproturon |\n3-(4-isopropilfenil)-N´,N´-dimetilurea | 9 | | Lindane | Isómero gama de 1,2,3,4,5,6-hexacloro-\nciclohexano | . 2 | | MCPA | Ácido (4-cloro-2-metilfenoxi)acético | 2 | | Mecroprop | Ácido\n(RS)-2-(4-cloro-2-metilfenoxi)propiónico | 10 | | Methoxychlor |\n2,2-bis(p-metoxifenil)-1,1,1-tricloroetano | . 20 | | Metolachlor |\n2-cloro-N-(2-etil-6-metilfenil)-N-(2- metoxi-1-metiletil) acetamida. | 10 | | Molinate | S-etil\nhexahidro-1H-azepina-1-carbiotiota | 6 | | PCP | Pentaclorofenol | 9 | | Pendiméthaline |\nN-(1-etilpropil)-3,4-dimetil-2,6-dinitobenzamina | . 20 | | Permethrin | . 3-fenoxibenzil (1RS)-cis,\ntrans-3-(2,2- diclorovinil)- 2,2 dimetilciclopropanocarboxilato | . 20 | | Propanil | N-(3,4\ndiclorofenil)propionamida | . 20 | | Pyridate | O-(6-cloro-3-fenil-4-piridazin) S-octil carbono\ntiota | 100 | | . Simazine | . 2-cloro-4,6-bis(etilamino)-s-triazina. | 2 | | 2,4,5-T |\nÁcido-2,4,5-triclorofenoxi-acético | . 9 | | Trifluraline |\nα,α,α-Trifluoro-2,6-dinitro-N,N-dipropil-p-toluidina | . 20 |\n\n \n\n \n\na Corresponde a la suma de todos los isómeros.\n\n \n\nCUADRO 5 PARÁMETROS DE CALIDAD\nPARA SUSTANCIAS\n\nORGÁNICAS DE SIGNIFICADO PARA LA\nSALUD, EXCEPTO\n\nPLAGUICIDAS PARA EL CUARTO\nNIVEL: N4\n\n \n\n| Parámetro | Valor Máximo Admisible, µg/L |\n| --- | --- |\n| Alcanos Clorados |  |\n| Tetracloruro de carbono | 2 |\n| Diclorometano | 20 |\n| 1,2-dicloroetano | 30 |\n| 1,1,1-tricloroetano | 2000 |\n\n \n\n \n\n \n\n \n\n \n\n| Parámetro | Valor Máximo Admisible, µg/L |\n| --- | --- |\n| Etenos Clorados |  |\n| Cloruro de Vinilo | 5 |\n| 1,1-dicloroeteno | 30 |\n| 1,2-dicloroeteno | 50 |\n| Tricloroeteno | 70 |\n| Tetracloroeteno | 40 |\n\n \n\n \n\n| Parámetro | Valor Máximo Admisible, µg/L |\n| --- | --- |\n| Hidrocarburos Aromáticos |  |\n| Tolueno | 700 |\n| Xilenos | 500 |\n| Etilbenceno | 300 |\n| Estireno | 20 |\n| Benzo-alfa-pireno | 0,7 |\n\n \n\n \n\n \n\n| Parámetro | Valor Máximo Admisible, µg/L |\n| --- | --- |\n| Bencenos Clorados |  |\n| Monoclorobenceno | 300 |\n| 1,2-diclorobenceno | 1000 |\n| 1,4-diclorobenceno | 300 |\n| Triclorobencenos | 20 |\n\n \n\n \n\n| Parámetro | Valor Máximo Admisible, µg/L |\n| --- | --- |\n| Otros Compuestos Orgánicos |  |\n| di (2-etilhexil) adipato | 80 |\n| di (2-etilhexil) ftalato | 8 |\n| Acrilamida | 0,5 |\n| Epiclorohidrino | 0,4 |\n| Hexaclorobutadieno | 0,5 |\n| EDTA | 200 |\n| Acido nitriloacético | 200 |\n| Oxido de tributilestaño | 2 |\n| Hidrocarburos policíclicos aromáticos totales | 0,2 |\n| Bifenilos policlorados totales | 0,5 |\n\n \n\n \n\nCUADRO 6. PARÁMETROS DE CALIDAD\nDEL AGUA\n\n-         \nCUARTO NIVEL - N4\n\n \n\n \n\n| Parámetro | Unidad | Valor Recomendado | Valor Máximo Admisible |\n| --- | --- | --- | --- |\n| Sólidos totales |  |  |  |\n| disueltos | mg/L |  | 1000 |\n| Amonio | mg/L NH4+ | 0,05 | 0,5 |\n| Sulfuro de Hidrógeno | mg/L H2S |  | 0,05 |\n\n \n\n \n\n \n\nCUADRO 7. PARÁMETROS PARA\nDESINFECTANTES Y\n\nSUBPRODUCTOS DE LA DESINFECCIÓN\n\nPARA EL CUARTO NIVEL: N4\n\n \n\n \n\n| Parámetro | Unidad | Valor Recomendado | Valor Máximo Admisible |\n| --- | --- | --- | --- |\n| Desinfectantes |  |  |  |\n|  | Monocloramina |  | 4000 |\n| Subproductos de la desinfección |  |  |  |\n|  | Bromato |  | 25 |\n|  | Clorito |  | 200 |\n| a- Clorofenoles |  |  |  |\n|  | 2,4,6-triclorofenol |  | 200 |\n|  | Formaldehido |  | 900 |\n| b- Trihalometanos |  |  |  |\n|  | Bromoformo |  | 100 |\n|  | Dibromoclorometano |  | 100 |\n|  | Bromodiclorometano |  | 60 |\n|  | Cloroformo |  | 200 |\n| c- Ácidos Acético Clorados |  |  |  |\n|  | Ác. Dicloroacético |  | 50 |\n|  | ác. Tricloroacético |  | 100 |\n|  | tricloracetaldehído/cloralhidrato |  | 100 |\n| d- Haloacetonitrilos |  |  |  |\n|  | Dicloroacetonitrilo |  | 90 |\n|  | Dibromoacetonitrilo |  | 100 |\n|  | Tricloroacetonitrilo |  | 11 |\n| e- Cloruro de cianógeno (como CN-) |  |  | 70 |\n\nANEXO 2\n\n \n\nNIVELES DE CONTROL, FRECUENCIA\n\nY NÚMERO DE MUESTRAS\n\n \n\nCUADRO A. NIVELES DE CONTROL Y\nPARÁMETROS 1\n\n \n\n \n\n| Parámetros a incluir | Nivel Primero (N 1 ) | Nivel Segundo (N 2 )\\| | Nivel Tercero (N 3 ) |\nNivel Cuarto ( N 4) | | --- | --- | --- | --- | --- | | a.Parámetros | - Color |  |  |  | |\nOrganolépticos | Aparente | Análisis (N1) + | Análisis (N2) + |  | |  | Turbiedad |  |  |  | |  |\nOlor 2 |  |  |  | |  | Sabor 2 |  |  |  | | b.Parámetros físico-químicos | - Temperatura 3 | Dureza\ntotal |  | - Sólidos totales | |  | - pH | - Cloruro - |  | Disueltos | |  | Conductividad | Nitrato\n|  |  | |  | Cloro residual - | Sulfato |  |  | |  | libre4 | Aluminio |  |  | |  | Cloro residual |\nCalcio |  |  | |  | combinado4 | Magnesio |  |  | |  |  | Sodio |  |  | |  |  | Potasio |  |  | |  |\n| Zinc |  |  | |  |  | Cobre |  |  | | -c.Parámetros - para sustancias inorgánicas con significado a\nla salud y plaguicidas |  | Hierro - | Amonio - | Sulfuro | |  |  | - Manganeso | - Nitrito - |\nHidrógeno | |  |  | Fluoruro |  |  | | d.Parámetros Tóxicos(orgánicos e inorgánicos). |  | Nitrato |\n- Arsénico - | Subproductos | |  |  | - Plomo | - Cadmio | de la desinfección | |  |  |  | - - Cromo\n| Cianuros | |  |  |  | - Mercurio | - Desinfectantes | |  |  |  | Níquel | Sustancias | |  |  |  |\nAntimonio | orgánicas con | |  |  |  | Selenio | significado para | |  |  |  | Residuos de\nplaguicidas | la salud | | e.Parámetros biológicos y microbiológicos | -Coliforme fecal |  |  | Los\nindicados, n el inciso 6.4, el artículo 6. | |  | - E. Coli 5 |  |  |  |\n\n \n\n \n\n \n\nRECOMENDACIÓN: Se recomienda adicionar un análisis\n(llamado rimer análisis), que sobre todo ha de llevarse a cabo antes de la\npuesta en marcha del sitio de muestreo. Los parámetros a tomar en cuenta serían\nlos del análisis de control normal, a los cuales podrían agregarse, entre\notros, con base en el riesgo detectado por la inspección sanitaria, diferentes\nsustancias tóxicas no deseadas. La lista será definida por el Ministerio de\nSalud, en consulta con el Instituto Costarricense de Acueductos y\nAlcantarillados.}\n\n \n\nNOTAS:\n\n \n\n1 El Ministerio de Salud y el A y A podrán utilizar\notros parámetros diferentes a los mencionados en el Anexo si es que surgen\nsituaciones especiales o de emergencia, o debido a factores que incidan\nnegativamente sobre la calidad del agua potable suministrada.\n\n2 Valoración cualitativa.\n\n3 Excepto para agua en depósitos cerrados.\n\n4 U otras sustancias, en caso de tratamiento con\ncloro.\n\n5 Confirmación en caso de que se detecte la presencia\nde Coliforme Fecal.\n\n \n\n \n\nCUADRO B. FRECUENCIA MÍNIMA DE\nANÁLISIS Y\n\nNÚMERO DE MUESTRAS 1\n\n \n\n \n\n            Ver\ncuadro en La Gaceta impresa N° 84 del 3 de mayo del 2005.\n\n \n\n \n\n 1 La\nfrecuencia y número de muestras para los análisis del nivel 4, serán\n\nestablecidos\nde acuerdo a cada situación particular (brotes de enfermedades de origen\nhídrico, contaminaciones accidentales, otros).\n\na En\ncada visita, se deberá recolectar muestras bacteriológicas en las\n\nfuentes\ny el almacenamiento y la red de distribución. Los puntos de análisis físico-químicos,\nen la red de distribución, son los mismos de los bacteriológicos, pero con\nfrecuencia semestral o trimestral, cuando se tenga identificada la línea base\nde calidad. El procedimiento de recolección de muestras en estructuras de\nalmacenamiento debe asegurar la representatividad de la muestra.\n\nb c\nEn estos niveles solamente, se recolectan muestras en las fuentes de\n\nabastecimiento,\na no ser que la inspección sanitaria lo establezca, para la red de\ndistribución.\n\nd una\nmuestra adicional, por cada 5 000 habitantes.\n\ne una\nmuestra adicional por cada 10 000 habitantes",
  "body_en_text": "in the full text\n\n                    -\n\n                        Complete Text of Regulation 32327\n\n                        Regulation for Drinking Water Quality\n\nComplete Text of Act: 106099\nNº 32327\n\nNº 32327\n\n(This executive decree was repealed by Article 20 of the Regulation for Drinking Water Quality, approved by executive decree N° 38924 of January 12, 2015)\n\nTHE PRESIDENT OF THE REPUBLIC\n\nAND THE MINISTER OF HEALTH\n\n \n\nIn exercise of the powers conferred by Articles 140 subsections 3), 18), and 146) of the Political Constitution; 28 subsection b) of the General Public Administration Act; 1, 2, 4, 7, 264, 265, 266, 267 and subsequent and concordant articles of the General Health Act (Ley Nº 5395 of October 30, 1973).\n\n \n\nConsidering:\n\n \n\nI.- That it is the duty of the State, through its institutions, to ensure public health.\n\nII.- That for this reason it is necessary and timely to issue the standards related to the quality of water for human consumption.\n\nIII.- That public and private entities acting as operators of drinking water aqueducts must comply with the provisions of this regulation in order to guarantee water quality.\n\nIV.- That the Ministry of Health, having the mission of ensuring public health, must regulate water quality by regulation and thus prevent diseases in humans caused by water contamination. Therefore:\n\nTHEY DECREE:\n\nRegulation for Drinking Water Quality\n\n \n\nCHAPTER I\n\nGeneral Provisions and Definitions\n\nArticle 1.-Objective and Scope. The objective of this regulation is to establish the maximum levels that those components or characteristics of water that may represent a risk to the health of the community and drawbacks for the preservation of water supply systems must have, for the benefit of public health.\n\nArticle 2.-Definitions and Units. For a better understanding of this regulation, the following definitions and table of units are established:\n\n \n\na) Accreditation: Procedure by which an authorized entity grants formal recognition that an organization or person is competent to carry out specific tasks.\n\nb) Drinking water: Treated water that complies with the provisions of recommended values or maximum admissible aesthetic, organoleptic, physical, chemical, biological, and microbiological values established in this regulation and that, when consumed by the population, does not cause damage to health.\n\nc) Surface water: Water originating from atmospheric precipitation, upwelling of groundwater (rivers, springs, lakes, streams). \n\nd) Groundwater: Water originating from infiltration through formations of one or more underground layers of rocks or other geological strata that have sufficient permeability to allow a significant flow that can be sustainably used for extraction. \n\ne) Treated water: Groundwater or surface water whose quality has been modified through treatment processes that include at least disinfection in the case of waters of underground origin. Its quality must conform to what is established in this regulation.\n\nf) Drinking water quality control: continuous and systematic evaluation of water quality from the source, treatment plant, storage systems, and distribution, according to specific programs that the operating entities must execute in order to comply with quality standards. \n\ng) Water disinfection: corresponds to a unit physical-chemical process whose objective is to guarantee the inactivation or destruction of pathogenic agents in the water to be used for human consumption. The chemical process of disinfection does not correspond to sterilization. \n\nh) Sanitary inspection: corresponds to visits, as a component of drinking water quality surveillance, for the application of field sheets that allow reviewing the state of the different structures (intakes, storage, distribution) of a water supply system for human consumption and the areas of influence to the intakes, to identify the risks that may affect its quality.\n\ni) Water sample: It is a portion of water that is collected in such a way that it is representative of a larger volume of liquid.\n\nj) PAHO / WHO: Pan American Health Organization / World Health Organization. \n\nk) Operating entities: institutions, companies, administering associations, or entities in general, public or private, directly in charge of the operation, maintenance, and administration of drinking water supply systems. \n\nl) Water redisinfection: application of a disinfectant to the water at one or more points of the distribution system such as: network, storage, and pumping station after prior treatment with the disinfectant to comply with the values established in the table of Article 12 of Chapter V. \n\nm) Maximum admissible value: corresponds to that concentration of a substance or density of bacteria from which rejection of the water by consumers occurs or an unacceptable risk to health arises. Exceeding these values indicated in the tables contained in Annex 1 implies taking immediate corrective actions. \n\nn) Recommended value: corresponds to that concentration of a substance or density of bacteria that implies a minimal or acceptable risk to the health of drinking water consumers.\n\nñ) Drinking water quality surveillance: is the permanent evaluation from the public health point of view, carried out by the Ministry of Health, on the operating entities, in order to guarantee the safety, harmlessness, and acceptability of the drinking water supply from the source's area of influence to the distribution system.\n\n \n\n \n\n| mg/L | Milligrams per liter | | --- | --- | | ppm | Parts per million | | µg/L | Micrograms per liter | | µS/cm | Micro siemens per centimeter | | PH | Potential of hydrogen ions | | U Pt-Co | Platinum cobalt units (for Color) | | UNT | Nephelometric Turbidity Units | | °C | Degrees Celsius | | NMP/100mL | Most Probable Number of bacteria in 100 milliliters of water, by the multiple tube fermentation method | | UFC/100mL | Colony Forming Units in 100 milliliters of water, by the membrane filter method | | UFC/ mL | Colony Forming Units in one milliliter of water |\n\nArticle 3.-For purposes of the scope of application of this regulation, it is established that the level of drinking water quality surveillance corresponds to the Ministry of Health and the levels of administration, control, and execution to the operating entities. \n\nArticle 4.-This regulation establishes the basic requirements that the drinking water supplied by the operating entities must meet.\n\nCHAPTER II\n\nScope of Application\n\n \n\nArticle 5.-For all regulatory effects on the quality of the drinking water supplied, the operating entities shall comply with this regulation, which contains the values for the physical, chemical, biological, and microbiological parameters in their aesthetic, organoleptic, and health-significant aspects established in tables 1, 2, 3, 4, 5, 6, and 7 of Annex 1.\n\nArticle 6.-This regulation establishes four levels of Water Quality Control (see Annex 2, table A):\n\n \n\n6.1 First Level (N1): corresponds to the basic control program together with the sanitary inspection, to evaluate the operation and maintenance at the source, storage, and distribution of drinking water. The parameters at this level are: thermotolerant (fecal) coliforms, Escherichia coli, apparent color, turbidity, odor, taste, temperature, pH, conductivity, and free or combined residual chlorine. The recommended and maximum admissible values are indicated in table 1 of Annex 1. If the sanitary inspection establishes other contamination risks, the necessary parameters must be added to the basic control program.\n\n6.2 Second Level (N2): corresponds to the extended basic control program (N1), the analysis of temporal trends of quality variations in the supply sources, to be applied to drinking water samples at the source, its storage, and distribution. The parameters at this control stage are all those established in level N1, expanded with: total hardness, chloride, fluoride, nitrate, sulfate, aluminum, calcium, magnesium, sodium, potassium, iron, manganese, zinc, copper, lead. The recommended and admissible values are indicated in table 2 of Annex 1.\n\n6.3 Third Level (N3): corresponds to the advanced control program for drinking water. It comprises the execution of the parameters of level N2 expanded with: nitrite, ammonium, arsenic, cadmium, chromium, mercury, nickel, antimony, selenium, and pesticide residues. The recommended and maximum admissible values are indicated in tables 3 and 4 of Annex 1.\n\n6.4 Fourth Level (N4): corresponds to occasional programs executed due to special or emergency situations or because the sanitary inspection identifies an imminent risk of water contamination. The parameters to be analyzed, depending on the identified situation, may be: total dissolved solids, hydrogen sulfide, cyanides, organic substances of health significance, disinfectants, and disinfection by-products. The recommended and maximum admissible values are indicated in tables 5, 6, and 7 of Annex 1. Other parameters such as: Shigella sp, Salmonella sp., Fecal streptococci, toxigenic Vibrio cholerae O1, Aeromonas hydrophila, nematodes, Entamoeba histolytica, Cryptosporidium, Hepatitis A Virus, Enteroviruses, and toxic cyanobacteria, must be absent in the analyzed samples. Total coliforms can be used as indicators of a system's vulnerability.\n\n \n\n \n\nThe Ministry of Health or the operating entity may expand the control parameters required for each situation. The operating entity shall send the results of the drinking water quality control to the Ministry of Health.\n\nArticle 7.-Public and private entities that act as public service operators must take the required actions to ensure compliance with:\n\n \n\n7.1 The control program up to the first level in all aqueducts in the country\n\n7.2 The control program up to the second level in all aqueducts with a supplied population exceeding 10,000 inhabitants\n\n7.3 The control program up to the third level in all aqueducts with a supplied population exceeding 50,000 inhabitants\n\nArticle 8.-Analysis Methods and Laboratories.\n\n \n\n8.1 Preferably, the reference methods for analysis are those indicated in the latest edition of the Standard Methods for the Examination of Water and Wastewater and the test methods accredited in accordance with the provisions of Ley Nº 8279 of May 2, 2002, (National System for Quality) Published in the Official Gazette La Gaceta Nº 96 of May 21, 2002.\n\n8.1 Laboratories that perform water analyses contemplated in this regulation must have an operating permit granted by the Ministry of Health according to Decreto 30465-S. (General Regulation for the Granting of Operating Permits by the Ministry of Health) of May 9, two thousand two, published in the Official Gazette La Gaceta Nº 102 on May 29, two thousand two.\n\nArticle 9.-When the maximum admissible value is exceeded, it is necessary for the operating entity to proceed to:\n\n \n\n9.1 Carry out a sanitary inspection with resampling, to identify the causes of the quality change and execute corrective actions.\n\n9.2 Consult the responsible national authorities: Ministry of Health, A y A, so that they provide advice on the degree of risk and the priority of corrective actions.\n\n9.3 The public and private entities that act as operators, in accordance with the degree of risk, must submit to the Ministry of Health the report of corrective actions executed and a plan of activities to prevent the event from recurring.\n\nCHAPTER III\n\nQuality Control Program\n\n \n\nArticle 10.-To implement the Water Quality Control Program, the operating entity must comply, at a minimum, with:\n\n \n\n10.1 Identify the supply zone.\n\n \n\n10.1a The supply zone corresponds to the geographic area of the system, with homogeneous characteristics in relation to the source and its related components: storage and sector of the distribution network.\n\n10.1b In systems with more than one source, sample collection must be carried out taking into account the number of inhabitants supplied by each source.\n\n \n\n10.2 Sample collection points.\n\n \n\n10.2a The sample collection points must be selected so that they are representative of the supply zones; starting with the source, storage, and ending in the distribution network. The sampling tap must be located as close as possible to the domestic connection controlled by the operator, free from the influence of the cistern, elevated tank, or any other type of intra-domiciliary water storage. 10.2b They must be uniformly distributed in each supply zone.\n\n10.2c The number of bacteriological and physical-chemical samples in the distribution network must be proportional to the number of inhabitants served in each supply zone. 10.2d They must be located: at the outlet of the treatment plant, outlet of storage tanks, outlet of underground sources (wells, springs, infiltration galleries, etc.), in the primary and secondary distribution network.\n\n \n\n10.3 Frequency of sample collection In order to ensure that the supply water meets the requirements of this Regulation, it is necessary to collect samples with the periodicity established in table B of Annex 2.\n\n \n\n10.4 Risk and vulnerability control program. \n\n \n\n10.4a Carry out the sanitary inspection of each of the aqueduct elements once a year, during a sample collection from the quality control program. \n\n10.4b Evaluate the results of the sanitary inspection, together with the last year of analysis data obtained in the quality control program.\n\n10.4c Define the degree of risk to health in each of the system's elements, as well as the prioritization of corrective actions.\n\nCHAPTER IV\n\nSanitary Surveillance of Water Quality Program\n\n \n\nArticle 11.-It is the responsibility of the Ministry of Health, through the different management levels, to carry out the evaluation of the operating entity from the operational point of view and its capacity to implement improvements, in order to reduce the degree of risk to the health of the population and the vulnerability of the systems.\n\nCHAPTER V\n\nDisinfection\n\n \n\nArticle 12.-Use of disinfection. The disinfection process is used as part of a series of unit operations and treatment processes in a plant. In its simplest form, it is applied as the sole treatment of natural waters of excellent quality (groundwater or spring water) to guarantee the absence of fecal contamination indicators between the point of application and the point of delivery to the user. Disinfection must also be applied to maintain a residual level, as indicated in Article 13, that guarantees water quality against eventual contamination throughout the entire distribution system.\n\nArticle 13.-Disinfectant dose. The disinfectant dose corresponds to the amount in parts per million (mg/L) that is applied to the water. The dose to be applied varies with the demand of each specific water.\n\n \n\n13.1 Disinfection with chlorine\n\n \n\nIt is a function of the type of residual present. For the destruction of indicator bacteria, the minimum chlorine level recommended in the distribution network, depending on the pH of the water and the minimum contact time, is given in the following table.\n\n \n\n| pH Value | Free residual chlorine (mg/L) Minimum Contact Time of 20 minutes | Combined residual chlorine (mg/L) Minimum Contact Time of 60 minutes | | --- | --- | --- | | 6.0 - 7.0 | 0.3 | 1.0 | | 7.1 - 8.0 | 0.5 | 1.5 | | 8.1 - 9.0 | 0.6 | 1.8 |\n\n \n\n \n\n13.2 Disinfection with ozone\n\n \n\nTo disinfect one cubic meter of water, 0.5 to 2 grams of ozone are used in practice, depending on the quality of the treated water. The residual at the point of application must be 0.3 to 0.4 mg/L, for 3 to 4 minutes of minimum contact time.\n\nArticle 14.-Dosing points\n\n \n\n14.1 The addition points for disinfectants are at the outlet of the plant's treatment processes, ensuring that there is an adequate contact period before the water enters the distribution system.\n\n14.2 Redisinfection points: These application points can be:\n\n14.2a At the end of a long feeder line within the distribution system.\n\n14.2b At a point where a main pipe diverts water to another nearby community.\n\n14.2c At a point in the system where there is a pumping station, in the storage tank.\n\nCHAPTER VI\n\nFinal Provisions\n\n \n\nArticle 15.-Every operating entity of water supply systems is obliged to deliver copies of its Water Quality Control program reports to the Ministry of Health.\n\nArticle 16.-In case of an emergency qualified as such by the health authorities in accordance with this regulation, the operating entity must:\n\n \n\n16.1 Suspend the supply service.\n\n16.2 Ensure the water supply by another means.\n\n16.3 Apply the corresponding corrective actions.\n\n16.4 Start operating the system once water quality is assured.\n\nArticle 17.-Surface water, without the respective treatment, must not be introduced into drinking water supply systems. The operating entity must ensure the sanitary quality of the water within the storage and distribution system throughout the year. \n\nArticle 18.-Annexes 1 and 2 referred to in previous articles form an integral part of this regulation.\n\nArticle 19.-This regulation shall enter into force eight days after its publication in the Official Gazette La Gaceta. \n\nArticle 20.-This Decree repeals Decreto Ejecutivo Nº 25991-S of April 14, 1997, published in La Gaceta on May 27, 1997.\n\n \n\nGiven at the Presidency of the Republic.-San José, on the tenth day of February, two thousand five.\n\nANNEX 1\n\n \n\nTABLE 1. WATER QUALITY PARAMETERS\n\n- FIRST LEVEL OF CONTROL - N1\n\n \n\n| Parameter | Unit | Recommended Value | Maximum Admissible Value | | --- | --- | --- | --- | | Fecal coliform | NMP/100 mL or UFC/100 mL | Absent | Absent | | Escherichia coliª | NMP/100 mL or UFC/100 mL | Absent | Absent | | Apparent color | mg/L (U - Pt-Co) | 5 | 15 b | | Turbidity | UNT | <1 | 5 b | | Odor | - | Must be acceptable | Must be acceptable | | Taste | - | Must be acceptable | Must be acceptable | | Temperature | ºC | 18 | 30 | | pHc | pH Value | 6.5 | 8.5 | | Conductivity | µS/cm | 400 |  | | Free Residual Chlorine | mg/L | 0.3 | 0.6 | | Combined Residual Chlorine | mg/L | 1.0 | 1.8 |\n\n \n\nTABLE 2. WATER QUALITY PARAMETERS\n\n- SECOND LEVEL OF CONTROL - N2\n\n \n\n| Parameter | Unit | Recommended Value | Maximum Admissible Value | | --- | --- | --- | --- | | Total Hardness | mg/L CaCO3 | 400 | 500 | | Chloride | mg/L Cl- | 25 | 250 | | Fluoride | mg/L F- |  | 0.7 to 1.5 a | | Nitrate | mg/L N0 3 | 25 | 50 | | Sulfate | mg/L S04 2 | 25 | 250 | | Aluminum | mg/L Al+3 | 0.2 |  | | Calcium | mg/L Ca+2 | 100 |  | | Magnesium | mg/L Mg+2 | 30 | 50 | | Sodium | mg/L Na+ | 25 | 200 | | Potassium | mg/L K+ |  | 10 | | Iron | mg/L Fe |  | 0.3 |\n\n \n\na The most precise bacteriological indicator of fecal contamination is Escherichia coli.\n\n b MAV in no more than 10% of the samples analyzed during the year.\n\n c Waters must be stabilized so that they do not produce corrosive or scaling effects in the aqueducts or in domestic utensils used to heat or boil water.\n\n \n\n \n\n| Parameter | Unit | Recommended Value | Maximum Admissible Value | | --- | --- | --- | --- | | Manganese | mg/L Mn | 0.1 | 0.5 | | Zinc | mg/L Zn |  | 3.0 | | Copper | mg/L Cu | 1.0 | 2.0 | | Lead | mg/L Pb |  | 0.01 |\n\n \n\n \n\na 1.5 mg/L for temperatures of 8 to 12 ºC and 0.7 mg/L for temperatures of 25 to 30 ºC\n\n \n\n \n\nTABLE 3. WATER QUALITY PARAMETERS\n\n-THIRD LEVEL OF CONTROL- N3\n\n \n\n| Parameter | Unit | Recommended Value | Maximum Admissible Value | | --- | --- | --- | --- | | Nitrite | mg/L NO2 |  | 0.1 or 3.0 a | | Ammonium | mg/L NH4 | 0.05 | 0.5 | | Arsenic | mg/L As |  | 0.01 | | Cadmium | mg/L Cd |  | 0.003 | | Chromium | mg/L Cr |  | 0.05 | | Mercury | mg/L Hg |  | 0.001 | | Nickel | mg/L Ni |  | 0.02 | | Antimony | mg/L Sb |  | 0.005 | | Selenium | mg/L Se |  | 0.01 |\n\n \n\n \n\na __ MAV of 0.1, if nitrite is evaluated independently of nitrate.\n ___ MAV of 3.0, when nitrite is evaluated jointly with nitrate. In this case, the sum of the concentration ratio of each with respect to its maximum admissible value must not exceed 1.0.\n\n \n\nSee formula in the printed Gazette N° 84 of May 3, 2005.\n\n \n\nNote: M.A.V. = Maximum Admissible Value.\n\n \n\n \n\nTABLE 4. QUALITY PARAMETERS FOR PESTICIDE RESIDUES\n\nTHIRD LEVEL OF CONTROL- N3\n\n \n\n| Parameter Active Ingredient ISO, BSI, ANSI | IUPAC Chemical Name | Maximum Admissible Value µg/L | | --- | --- | --- | | Alachlor | 2-chloro-2,6-diethyl (methoxymethyl)acetanilide | 20 | | Aldicarb | 2-methyl-2-(methylthio)propionaldehyde O- (methylcarbamoyl) oxime. | 10 | | Aldrin/dieldrin | (1R,4S,4aS,5S,8R,8aR)-1,2,34,10,10- hexachloro-1,4,4a,5,8,8a-hexahydro-1,4:5,8 - dimethanonaphthalene | . 0.03 | | Atrazine | 6-chloro-N2-ethyl-N4-isopropyl-1,3,5-triazine-2,4- diamine | 2 | | Bentazone | 3-isopropyl-1H-2,1,3-benzothiadiazin-4(3H)- one-2,2-dioxide. | 300 | | Carbofuran | 2,3-dihydro-2,2-dimethyl-7-benzofuranyl-methylcarbamate. | 7 | | Chlordane | 1,2,4,5,6,7,8,8-octachloro-2,3,3a,4,7,7ahexahydro- 4,7-methanoindene | . 0.2 | | 2,4-D | 2,4-dichlorophenoxyacetic acid. | 30 | | 2,4-DB | 4-(2,4-dichlorophenoxy)butyric acid. | 90 | | DDTa | Dichloro-diphenyl-trichloroethane | . 2 | | Dibromochloropropane | 1,2-dibromo-3-chloropropane. | . 1 | | Dichloropropene | 1,3-dichloropropene | . 20 | | Dichlorprop | (RS)-2-(2,4-dichlorophenoxy)propionic acid | 100 | | Heptachlor + epoxide | 1,4,5,6,7,8,8-heptachloro-3a,4,7,7a-tetrahydro- 4,7-methanoindene | . 0.03 | | Isoproturon | 3-(4-isopropylphenyl)-N´,N´-dimethylurea | 9 | | Lindane | Gamma isomer of 1,2,3,4,5,6-hexachloro- cyclohexane | . 2 | | MCPA | (4-chloro-2-methylphenoxy)acetic acid | 2 | | Mecoprop | (RS)-2-(4-chloro-2-methylphenoxy)propionic acid | 10 | | Methoxychlor | 2,2-bis(p-methoxyphenyl)-1,1,1-trichloroethane | . 20 | | Metolachlor | 2-chloro-N-(2-ethyl-6-methylphenyl)-N-(2- methoxy-1-methylethyl) acetamide. | 10 | | Molinate | S-ethyl hexahydro-1H-azepine-1-carbothioate | 6 | | PCP | Pentachlorophenol | 9 | | Pendimethalin | N-(1-ethylpropyl)-3,4-dimethyl-2,6-dinitrobenzamine | . 20 | | Permethrin | . 3-phenoxybenzyl (1RS)-cis, trans-3-(2,2- dichlorovinyl)- 2,2 dimethylcyclopropanecarboxylate | . 20 | | Propanil | N-(3,4 dichlorophenyl)propionamide | . 20 | | Pyridate | O-(6-chloro-3-phenyl-4-pyridazinyl) S-octyl carbonothioate | 100 | | . Simazine | . 2-chloro-4,6-bis(ethylamino)-s-triazine. | 2 | | 2,4,5-T | 2,4,5-trichlorophenoxy-acetic acid | . 9 | | Trifluralin | α,α,α-Trifluoro-2,6-dinitro-N,N-dipropyl-p-toluidine | . 20 |\n\n \n\n \n\na Corresponds to the sum of all isomers.\n\n \n\nTABLE 5. QUALITY PARAMETERS FOR ORGANIC SUBSTANCES OF HEALTH SIGNIFICANCE, EXCEPT PESTICIDES FOR THE FOURTH LEVEL: N4\n\n \n\n| Parameter | Maximum Admissible Value, µg/L | | --- | --- | | Chlorinated Alkanes |  | | Carbon tetrachloride | 2 | | Dichloromethane | 20 | | 1,2-dichloroethane | 30 | | 1,1,1-trichloroethane | 2000 |\n\n \n\n \n\n \n\n \n\n \n\n| Parameter | Maximum Admissible Value, µg/L | | --- | --- | | Chlorinated Ethenes |  | | Vinyl Chloride | 5 | | 1,1-dichloroethene | 30 | | 1,2-dichloroethene | 50 | | Trichloroethene | 70 | | Tetrachloroethene | 40 |\n\n \n\n \n\n| Parameter | Maximum Admissible Value, µg/L | | --- | --- | | Aromatic Hydrocarbons |  | | Toluene | 700 | | Xylenes | 500 | | Ethylbenzene | 300 | | Styrene | 20 | | Benzo-alpha-pyrene | 0.7 |\n\n \n\n \n\n \n\n| Parameter | Maximum Admissible Value, µg/L | | --- | --- | | Chlorinated Benzenes |  | | Monochlorobenzene | 300 | | 1,2-dichlorobenzene | 1000 | | 1,4-dichlorobenzene | 300 | | Trichlorobenzenes | 20 |\n\n \n\n \n\n| Parameter | Maximum Admissible Value, µg/L | | --- | --- | | Other Organic Compounds |  | | di (2-ethylhexyl) adipate | 80 | | di (2-ethylhexyl) phthalate | 8 | | Acrylamide | 0.5 | | Epichlorohydrin | 0.4 | | Hexachlorobutadiene | 0.5 | | EDTA | 200 | | Nitriloacetic acid | 200 | | Tributyltin oxide | 2 | | Total polycyclic aromatic hydrocarbons | 0.2 | | Total polychlorinated biphenyls | 0.5 |\n\n \n\n \n\nTABLE 6. WATER QUALITY PARAMETERS\n\n- FOURTH LEVEL - N4\n\n \n\n \n\n| Parameter | Unit | Recommended Value | Maximum Admissible Value | | --- | --- | --- | --- | | Total dissolved |  |  |  | | solids | mg/L |  | 1000 | | Ammonium | mg/L NH4+ | 0.05 | 0.5 | | Hydrogen Sulfide | mg/L H2S |  | 0.05 |\n\n \n\n \n\n \n\nTABLE 7. PARAMETERS FOR DISINFECTANTS AND DISINFECTION BY-PRODUCTS\n\nFOR THE FOURTH LEVEL: N4\n\n \n\n \n\n| Parameter | Unit | Recommended Value | Maximum Admissible Value | | --- | --- | --- | --- | | Disinfectants |  |  |  | |  | Monochloramine |  | 4000 | | Disinfection By-products |  |  |  | |  | Bromate |  | 25 | |  | Chlorite |  | 200 | | a- Chlorophenols |  |  |  | |  | 2,4,6-trichlorophenol |  | 200 | |  | Formaldehyde |  | 900 | | b- Trihalomethanes |  |  |  | |  | Bromoform |  | 100 | |  | Dibromochloromethane |  | 100 | |  | Bromodichloromethane |  | 60 | |  | Chloroform |  | 200 | | c- Chlorinated Acetic Acids |  |  |  | |  | Dichloroacetic acid |  | 50 | |  | Trichloroacetic acid |  | 100 | |  | Trichloroacetaldehyde/chloral hydrate |  | 100 | | d- Haloacetonitriles |  |  |  | |  | Dichloroacetonitrile |  | 90 | |  | Dibromoacetonitrile |  | 100 | |  | Trichloroacetonitrile |  | 11 | | e- Cyanogen chloride (as CN-) |  |  | 70 |\n\nANNEX 2\n\n \n\nCONTROL LEVELS, FREQUENCY, AND NUMBER OF SAMPLES\n\n \n\nTABLE A. CONTROL LEVELS AND PARAMETERS 1\n\n \n\n \n\n| Parameters to include | First Level (N 1) | Second Level (N 2) | Third Level (N 3) | Fourth Level ( N 4) | | --- | --- | --- | --- | --- | | a. Organoleptic Parameters | - Apparent |  |  |  | |  | Color | Analysis (N1) + | Analysis (N2) + |  | |  | - Turbidity |  |  |  | |  | Odor 2 |  |  |  | |  | Taste 2 |  |  |  | | b. Physical-Chemical Parameters | - Temperature 3 | Total hardness |  | - Total dissolved | |  | - pH | - Chloride - |  | solids | |  | Conductivity | Nitrate |  |  | |  | Residual chlorine - | Sulfate |  |  | |  | free4 | Aluminum |  |  | |  | Combined residual | Calcium |  |  | |  | chlorine4 | Magnesium |  |  | |  |  | Sodium |  |  | |  |  | Potassium |  |  | |  |  | Zinc |  |  | |  |  | Copper |  |  | | - c. Parameters for inorganic substances with health significance and pesticides |  | Iron - | Ammonium - | Hydrogen | |  |  | - Manganese | - Nitrite - | Sulfide | |  |  | Fluoride |  |  | | d. Toxic Parameters (organic and inorganic). |  | Nitrate | - Arsenic - | Disinfection | |  |  | - Lead | - Cadmium | by-products | |  |  |  | - - Chromium | Cyanides | |  |  |  | - Mercury | - Disinfectants | |  |  |  | Nickel | Organic | |  |  |  | Antimony | substances with | |  |  |  | Selenium | health significance | |  |  |  | Pesticide residues |  | | e. Biological and Microbiological Parameters | -Fecal Coliform |  |  | Those indicated in subsection 6.4, Article 6. | |  | - E. Coli 5 |  |  |  |\n\n \n\n \n\n \n\nRECOMMENDATION: It is recommended to add an analysis (called the first analysis), which must be carried out above all before the commissioning of the sampling site. The parameters to be taken into account would be those of the normal control analysis, to which could be added, among others, based on the risk detected by the sanitary inspection, different unwanted toxic substances. The list will be defined by the Ministry of Health, in consultation with the Instituto Costarricense de Acueductos y Alcantarillados.\n\n \n\nNOTES:\n\n \n\n1 The Ministry of Health and A y A may use parameters other than those mentioned in the Annex if special or emergency situations arise, or due to factors that negatively affect the quality of the supplied drinking water.\n\n2 Qualitative assessment.\n\n3 Except for water in closed deposits.\n\n4 Or other substances, in case of treatment with chlorine.\n\n5 Confirmation in case the presence of Fecal Coliform is detected.\n\n \n\n \n\nTABLE B. MINIMUM FREQUENCY OF ANALYSIS AND NUMBER OF SAMPLES 1\n\n \n\n \n\n            See table in the printed Gazette N° 84 of May 3, 2005.\n\n \n\n \n\n 1 The frequency and number of samples for level 4 analyses shall be established according to each particular situation (outbreaks of waterborne diseases, accidental contaminations, others).\n\na At each visit, bacteriological samples must be collected at the sources, storage, and distribution network. The physical-chemical analysis points in the distribution network are the same as the bacteriological ones, but with a semi-annual or quarterly frequency, once the quality baseline has been identified. The sample collection procedure in storage structures must ensure the representativeness of the sample.\n\nb c\nAt these levels only, samples are collected at the supply sources, unless the sanitary inspection establishes otherwise, for the distribution network.\n\nd one additional sample, per 5,000 inhabitants.\n\ne one additional sample per 10,000 inhabitants."
}