{
  "id": "norm-55708",
  "citation": "Decreto 32692",
  "section": "norms",
  "doc_type": "executive_decree",
  "title_es": "Procedimiento para la Medición de Ruido",
  "title_en": "Noise Measurement Procedure",
  "summary_es": "El Decreto Ejecutivo N° 32692 establece el procedimiento técnico oficial para la medición de ruido por parte de las autoridades de salud, con el fin de proteger a la población de la contaminación sónica proveniente de fuentes artificiales. La norma define conceptos clave como ruido, nivel de presión sonora y tipos de ruido (continuo, intermitente, de impacto). Detalla los requisitos previos a la medición, incluyendo la identificación de afectados y la calibración del sonómetro según estándares ANSI e IEC. Especifica las condiciones para realizar las mediciones: colocación del equipo a 1,5 m del suelo y a 0,5 m del cuerpo del funcionario, uso de pantalla antiviento, realización de al menos 15 mediciones cada 15 segundos, y descarte de ruidos ocasionales. Incluye métodos numérico y gráfico para el cálculo de la suma de niveles de presión sonora. Exige un informe técnico detallado y, si se exceden los límites legales, ordena al Ministerio de Salud emitir una Orden Sanitaria que requiere un plan de confinamiento de ruido y planos constructivos para visado sanitario. Este decreto fue derogado en 2024 por el Reglamento para el control del ruido ambiental (Decreto N° 44486).",
  "summary_en": "Executive Decree No. 32692 establishes the official technical procedure for noise measurement by health authorities, aiming to protect the population from noise pollution from artificial sources. It defines key concepts such as noise, sound pressure level, and types of noise (continuous, intermittent, impact). It details prerequisites for measurement, including identification of affected persons and calibration of the sound level meter according to ANSI and IEC standards. It specifies measurement conditions: positioning the device 1.5 m above ground and 0.5 m from the officer’s body, use of a windscreen, performing at least 15 measurements every 15 seconds, and discarding occasional noises. It includes numerical and graphical methods for calculating the sum of sound pressure levels. It requires a detailed technical report and, if legal limits are exceeded, orders the Ministry of Health to issue a Sanitary Order demanding a noise confinement plan and construction plans for sanitary approval. This decree was repealed in 2024 by the Regulation for Environmental Noise Control (Decree No. 44486).",
  "court_or_agency": "",
  "date": "09/08/2005",
  "year": "2005",
  "topic_ids": [
    "_off-topic"
  ],
  "primary_topic_id": "_off-topic",
  "es_concept_hints": [
    "contaminación por ruido",
    "sonómetro",
    "nivel de presión sonora (Lp)",
    "dB(A)",
    "atenuación lento/rápido/pico",
    "plan de confinamiento de ruido",
    "DPAH",
    "calibración ANSI/IEC"
  ],
  "concept_anchors": [
    {
      "article": "",
      "law": "Ley General de Salud"
    },
    {
      "article": "Art. 50",
      "law": "Constitución Política"
    }
  ],
  "keywords_es": [
    "ruido",
    "medición de ruido",
    "sonómetro",
    "nivel de presión sonora",
    "contaminación sónica",
    "Ministerio de Salud",
    "orden sanitaria",
    "calibración",
    "decibelios",
    "fuente emisora"
  ],
  "keywords_en": [
    "noise",
    "noise measurement",
    "sound level meter",
    "sound pressure level",
    "noise pollution",
    "Ministry of Health",
    "sanitary order",
    "calibration",
    "decibels",
    "emitting source"
  ],
  "excerpt_es": "Artículo 1º-Objetivo y alcance. Oficialícese para efectos de aplicación por las autoridades de salud los procedimientos para la medición de ruido que debe efectuarse con el propósito de asegurar la protección a la salud de las personas en lo que se refiere a emisión contaminante de ruido, proveniente de fuentes artificiales.\nArtículo 6º-De las Mediciones. Los funcionarios responsables de las mediciones sónicas del Ministerio de Salud deberán de cumplir al menos con los siguientes aspectos al efectuar las mediciones: [...] c) Si el ruido es continuo se debe de utilizar la atenuación lento (slow) y se utilizará la atenuación rápida (fast) para medidas de corta duración [...] i) Deberán realizarse al menos 15 mediciones y anotarse los resultados correspondientes.",
  "excerpt_en": "Article 1—Objective and scope. The noise measurement procedures to be carried out for the purpose of ensuring the protection of people's health with regard to polluting noise emissions from artificial sources are hereby made official for application by the health authorities.\nArticle 6—Measurements. The officials responsible for sonic measurements of the Ministry of Health shall comply with at least the following aspects when performing the measurements: [...] c) If the noise is continuous, slow attenuation shall be used, and fast attenuation shall be used for short-duration measurements [...] i) At least 15 measurements shall be taken and the corresponding results recorded.",
  "outcome": {
    "label_en": "Repealed",
    "label_es": "Derogado",
    "summary_en": "The decree established the official procedure for noise measurement by health authorities but was repealed in 2024 by the Regulation for Environmental Noise Control.",
    "summary_es": "El decreto estableció el procedimiento oficial para la medición de ruido por autoridades de salud, pero fue derogado en 2024 por el Reglamento para el control del ruido ambiental."
  },
  "pull_quotes": [
    {
      "context": "Artículo 1",
      "quote_en": "The noise measurement procedures to be carried out for the purpose of ensuring the protection of people's health with regard to polluting noise emissions from artificial sources are hereby made official for application by the health authorities.",
      "quote_es": "Oficialícese para efectos de aplicación por las autoridades de salud los procedimientos para la medición de ruido que debe efectuarse con el propósito de asegurar la protección a la salud de las personas en lo que se refiere a emisión contaminante de ruido, proveniente de fuentes artificiales."
    },
    {
      "context": "Artículo 6, inciso i)",
      "quote_en": "At least 15 measurements shall be taken and the corresponding results recorded.",
      "quote_es": "Deberán realizarse al menos 15 mediciones y anotarse los resultados correspondientes."
    },
    {
      "context": "Artículo 9",
      "quote_en": "If the results of the previous article indicate that the noise produced by the emitting source(s) exceeds what is established by current legal regulations, the Ministry of Health shall issue the corresponding Sanitary Order...",
      "quote_es": "En caso de que los resultados del artículo anterior indiquen que el ruido producido por la(s) fuente(s) emisora(s) sobrepasa(n) lo establecido por la normativa jurídica vigente, el Ministerio de Salud procederá a girar la Orden Sanitaria correspondiente..."
    }
  ],
  "cites": [],
  "cited_by": [],
  "references": {
    "internal": [
      {
        "target_id": "nexus-sen-1-0034-930193",
        "kind": "cited_by_voto",
        "label": "Tribunal Contencioso Administrativo Sección III Res. 00320-2019"
      }
    ],
    "external": []
  },
  "source_url": "https://pgrweb.go.cr/scij/Busqueda/Normativa/Normas/nrm_texto_completo.aspx?param1=NRTC&nValor1=1&nValor2=55708&strTipM=TC&nValor3=0",
  "tier": 2,
  "_editorial_citation_count": 0,
  "regulations_by_article": null,
  "amendments_by_article": null,
  "dictamen_by_article": null,
  "concordancias_by_article": null,
  "afectaciones_by_article": null,
  "resoluciones_by_article": null,
  "cited_by_votos": [
    {
      "doc_id": "nexus-ext-1-0034-269127",
      "parent_doc_id": "nexus-sen-1-0034-930193",
      "despacho": "Tribunal Contencioso Administrativo Sección III",
      "date": "27-Jun-2019",
      "expediente": "180010421027CA",
      "redactor": "Evelyn de los Ángeles Solano Ulloa",
      "descriptores": "Recurso jerárquico impropio, Principio precautorio en materia ambiental",
      "restrictores": "Alcances de la competencia del Ministerio de Salud y la Municipalidad en asuntos relacionados con la legislación ambiental, Alcances e inaplicabilidad en caso del Complejo Deportivo Furati al ser descartado como causante de contaminación sónica",
      "tipoDocumento": "EXT",
      "numeroDocumento": "00320",
      "anno": "2019",
      "label": "Tribunal Contencioso Administrativo Sección III Res. 00320-2019",
      "url": "https://nexuspj.poder-judicial.go.cr/document/ext-1-0034-269127"
    }
  ],
  "cited_norms": [],
  "cited_norms_inverted": [],
  "sentencias_relacionadas": [],
  "temas_y_subtemas": [],
  "cascade_only": false,
  "amendment_count": 0,
  "body_es_text": "en la totalidad del texto\n\n                    -\n\n                        Texto Completo Norma 32692\n\n                        Procedimiento para la Medición de Ruido\n\nTexto Completo acta: 1710F0\nNº 32692\n\nNº 32692\n\n(Este decreto ejecutivo fue derogado por el artículo\n39 del Reglamento para el control del ruido ambiental, aprobado mediante\ndecreto ejecutivo N° 44486 del 17 de enero del 2024)\n\nEL PRESIDENTE DE LA\nREPÚBLICA\n\nY LA MINISTRA DE SALUD\n\n \n\nEn uso de las\nfacultades que les confieren los artículos 50, 140; incisos 3) y 18) y 146 de\nla Constitución Política; 2º, 4º, 7º, 37, 38, 263, 293, 325, 337, 338, 339,\n340, 341, 342, 347, 348, 349, 355, 357, 363, 364 y concordantes de la Ley N°\n5395 del 30 de octubre de 1973, \"Ley General de Salud\"; 6° de la Ley\nN° 5412 del 8 de noviembre de 1973, \"Ley Orgánica del Ministerio de\nSalud\"; 25, inciso 1) y 28, inciso b) de la ley número 6227 del 2 de Mayo\nde 1978, \"Ley General de Administración Pública\".\n\n \n\nConsiderando:\n\n \n\n1º-Que la salud de la\npoblación es un bien de interés público tutelado por el Estado.\n\n2º-Que es función del\nMinisterio de Salud dictar las disposiciones reglamentarias pertinentes, en\nespecial las que tengan relación con la contribución, promoción y mantenimiento\nde las condiciones del ambiente natural y de los ambientes artificiales que\npermitan garantizar las necesidades vitales y de salud de la población.\n\n3º-Que toda persona,\nnatural o jurídica queda sujeta a los mandatos de la Ley General de Salud, de\nsus reglamentos y de las órdenes generales y particulares, ordinarias y de\nemergencia, que las autoridades de salud dicten en el ejercicio de sus\ncompetencias.\n\n4º-Que la medición\nsónica constituye el medio técnico idóneo y la prueba fehaciente para comprobar\nla existencia de ruidos que pueden afectar la salud de la población por lo que\nse requiere emplear métodos que garanticen que los valores obtenidos sean\nconfiables y permitan decisiones correctas y acertadas en la materia.\n\n5º-Que se hace\nnecesario y oportuno establecer un procedimiento para medir el ruido.\n\n6º-Que el Decreto\nEjecutivo Nº 18209-S publicado en el Diario Oficial La Gaceta Nº 133 del\n13 de julio de 1988, que a su vez reformó los artículos 6º y 50 del D. E. Nº\n11492-S del 22 de abril de 1980 (Reglamento sobre Higiene Industrial) señaló\nque la actual Dirección de Protección al Ambiente Humano del Ministerio de\nSalud establecerá los procedimientos de acuerdo con las normas establecidas\npara efectuar las pruebas de medición. Por tanto,\n\n \n\nDECRETAN:\n\n \n\nProcedimiento\npara la Medición de Ruido\n\n \n\nArtículo 1º-Objetivo\ny alcance. Oficialícese para efectos de aplicación por las autoridades de\nsalud los procedimientos para la medición de ruido que debe efectuarse con el\npropósito de asegurar la protección a la salud de las personas en lo que se\nrefiere a emisión contaminante de ruido, proveniente de fuentes artificiales.\n\nArtículo 2º-Competencia de\naplicación. La aplicación de este Reglamento es competencia de las\nautoridades de salud.\n\nArtículo 3º-Definiciones.\nPara fines de este Reglamento se entenderá por:\n\n \n\na) Autoridad de Salud:\nMinisterio de Salud.\n\n \n\nb) Certificado de Calibración:\nDocumento que extiende la Casa Matriz o Laboratorio Acreditado que hace constar\nque los equipos han sido revisados y sus desviaciones electrónicas se\nencuentran dentro de los límites especificados por sus fabricantes y cumplen\ncon los estándares ANSI y IEC. Tiene una vigencia de un año.\n\n \n\nc) Contaminación por ruido:\nCualquier emisión de sonido que afecte adversamente la salud de los seres\nhumanos.\n\n \n\nd) dB(A): Es la unidad de\nmedida del nivel sonoro cuando se usa la escala de ponderación A.\n\n \n\ne) Decibelio o Decibel (dB):\nUnidad adimensional usada para expresar el logaritmo de la razón entre una\ncantidad medida y una cantidad de referencia. De esta manera el dB es usado\npara describir niveles de presión, potencia o intensidad sonora.\n\n \n\nf) DPAH: Dirección de\nProtección del Ambiente Humano del Ministerio de Salud.\n\n \n\ng) Emisión: Emanación de\nruido a la atmósfera por una fuente emisora.\n\n \n\nh) Fuente Emisora: Cualquier\nobjeto o artefacto que origina una onda sonora, ya sea de tipo estacionario,\nmóvil o portátil.\n\n \n\ni) Nivel de presión sonora (Lp):\nEstá de.nida por: Lp= 20 log P1/Po (dB) donde:\n\n \n\nP1= Presión acústica existente\n(presión efectiva medida)\n\n \n\nPo = Presión acústica de referencia=\n2 x 10-5 pascales (Pa)= 20 micropascales (uPa).\n\n \n\nj) Medición de Ruido:\nOperación técnica que consiste en determinar los valores de los niveles de ruido\nprovenientes de una o varias fuentes emisoras.\n\n \n\nk) Nivel de Ruido: El nivel\nde presión de sonido medido mediante las características de medición y escalas\nA, B ó C, como lo especifica la \"American National Standards Institute\" (ANSI),\n\"Specification for Sound Level Meters\", última revisión.\n\n \n\nl) Ondas de Sonido: Son ondas\nque se producen cuando se perturba el aire y viajan a través del espacio\ntridimensional comúnmente como ondas sinusoidales longitudinales progresivas.\nLa propagación de las ondas sonoras implica la transferencia de energía\n(parcialmente cinética y parcialmente potencial) a través del espacio.\n\n \n\nm) Persona: Toda persona,\nfísica o jurídica, o grupo de personas privadas o públicas.\n\n \n\nn) Plan de confinamiento de ruido:\nConsiste en aquellas acciones o medidas correctivas tendientes a encapsular,\nabsorver o disminuir el ruido dentro de la fuente emisora a .n de no afectar a\nterceros.\n\n \n\no) Ruido: Sonido o conjunto\nde sonidos mezclados y desordenados, indeseable o perturbante que afecte\npsicológica, físicamente o de cualquier otra manera al ser humano o que exceda\nlas limitaciones reglamentarias establecidas.\n\n \n\np) Ruido de fondo: Es el de\ntodas las fuentes distintas a la fuente concreta de sonido de interés (sonidos\ndiferentes del que se está midiendo).\n\n \n\nq) Ruido continuo: Es aquel\nque no tiene cambios rápidos o repentinos de nivel. Se caracteriza por niveles\nde presión sonora que no fluctúan rápidamente en el tiempo. Las flucutuaciones\nocurren a razón de uns pocos dB/segundo. Ejemplo: máquinas rotatorias, telares.\n\n \n\nr) Ruido intermitente: El\nruido que se interrumpe o cesa o se repite.\n\n \n\ns) Ruido de impacto: Ruido\nque tiene su causa en golpes simples de corta duración.\n\n \n\nt) Sonido: Una alteración\nfísica en un medio (por ejemplo aire) que puede ser detectada por el oído\nhumano.\n\n \n\nu) Sonómetro: Instrumento\nusado para medir los niveles de sonido.\n\nArtículo 4º-Requisitos previos a\nla Medición del Ruido.\n\n \n\na) Identificar y ubicar la(s)\npersona(s) afectada(s) con el fin de coordinar la hora y lugar de la realización\nde las mediciones sónicas.\n\n \n\nb) Contar con equipo de medición\n(sonómetro) y su respectivo calibrador.\n\n \n\nc) Las mediciones sónicas deben de\nser efectuadas por dos funcionarios del Ministerio de Salud como mínimo.\n\nArtículo 5º-Calibración del\nEquipo. Antes de efectuarse la medición debe verificarse que el equipo\ncuente con el Certificado de Calibración vigente.\n\nEl equipo debe calibrarse antes de\nla medición para lo cual se utiliza el calibrador correspondiente.\n\nLa calibración debe realizarse\npreferiblemente en un ambiente donde no se esté generando ruido de fondo,\nsiguiendo las instrucciones del fabricante indicadas en el manual del equipo.\n\nTodo equipo de medición y de\ncalibración debe contar con su respectivo manual para su operación.\n\nArtículo 6º-De las Mediciones.\nLos funcionarios responsables de las mediciones sónicas del Ministerio de Salud\ndeberán de cumplir al menos con los siguientes aspectos al efectuar las\nmediciones:\n\n \n\na) Antes de efectuar cualquier tipo\nde medición deberá determinarse el nombre completo y el número de cédula de\nidentidad o pasaporte de las personas presentes durante la realización de las\nmediciones.\n\nAnotar fecha y hora de inicio y de\nfinalización de las mediciones.\n\n \n\nb) Identificar la(s) fuente(s)\ngeneradora(s) del ruido que se va(n) a medir.\n\n \n\nc) Si el ruido es continuo se debe\nde utilizar la atenuación lento (slow) y se utilizará la atenuación rápida\n(fast) para medidas de corta duración (por ejemplo campanas de una iglesia,\nsirenas, alarmas y otros similares). Si el ruido es de impacto se debe de\nemplear la atenuación pico (peak) siguiendo las instrucciones del Manual de Operación\ndel equipo. El sonómetro se debe colocar a una altura aproximada de 1,5 m del\nnivel del suelo y el ángulo formado entre el sonómetro y un plano inclinado paralelo\nal suelo debe encontrarse entre los 30 a 60 grados.\n\n \n\nd) Colocar el sonómetro a una\ndistancia libre mínima aproximada de 0,50 m del cuerpo del funcionario.\n\n \n\ne) En mediciones externas se debe\nutilizar la pantalla (rejilla o .ltro) antiviento que forma parte del equipo.\n\n \n\nf) Al efectuar las mediciones, se\ndebe evitar condiciones metereológicas extremas tales como lluvia, viento,\nrayería y otros que puedan afectar los resultados obtenidos y al equipo.\n\n \n\ng) Se debe asegurar que las\nmediciones se efectúen dentro de las edificaciones evitando fuentes emisoras de\nsonido ajenas a la medición. La medición deberá efectuarse con las ventanas\nabiertas y señalar el (los) sitio(s) del inmueble en que se realizaron.\n\n \n\nh) Cada medición debe realizarse\ncada 15 segundos.\n\n \n\ni) Deberán realizarse al menos 15\nmediciones y anotarse los resultados correspondientes.\n\nj) Deberán descartarse aquellas\nmediciones que incluyan ruidos ocasionales (entre otros: motocicletas con\nescape libre, sirenas de ambulancias o bomberos).\n\n \n\nk) Realizar mediciones de ruido\nambiente, para lo cual la fuente que se evalúa debe permanecer inactiva.\n\n \n\nl) Las mediciones, en caso de\nrepetición, deben realizarse bajo condiciones similares a las que se efectuaron\nanteriormente.\n\nArtículo\n7º—Cálculo de Niveles de Presión Sonora. Cuando sobre un mismo receptor\ninciden niveles de presión sonora provenientes de diferentes fuentes emisoras y se\nrequiere conocer el resultado de su suma se deben utilizar las propiedades de los\nlogaritmos.\n\nPara\nefectos de cálculo se usarán los siguientes métodos:\n\n \n\na)      \nMétodo\nnumérico: La\nmagnitud de Nivel de presión sonora en decibelios (dB), viene dada por la expresión:\n\n \n\nVer\nformulas en La Gaceta impresa N° 201 del 19 de octubre del 2005.\n\n \n\nEjemplo\npráctico:\n\n \n\nPara\ncalcular los niveles de presión sonora se debe proceder de la siguiente manera:\n\n \n\nN1 = 101 dB\n\n \n\nN2 = 84 dB\n\n \n\nN3 = 91 dB\n\n \n\nN4 = 97 dB\n\n \n\nN5 = 100 dB\n\n \n\nN6 = 101 dB\n\n \n\nN7 = 99 dB\n\n \n\nAplicando\na cada nivel de presión sonora la expresión anteriormente definida se obtienen los\nsiguientes valores:\n\n \n\nVer\nformulas en La Gaceta impresa N° 201 del 19 de octubre del 2005.\n\n \n\nb) Método\nGráfico: Si se tienen varios niveles de presión sonora y se quiere conocer la suma\nde éstos, utilizando la figura 1, se procede de la siguiente manera:\n\n \n\n1. Se\nordenan los niveles de mayor a menor.\n\n \n\n2. Se\nobtiene la diferencia entre el primero y el segundo.\n\n \n\n3. La\ndiferencia obtenida se lleva a las abscisas de la curva obteniendo en las ordenadas el\nvalor que hay que sumar al nivel mayor.\n\n \n\n4. Con\neste nivel-suma, así obtenido, se procede a realizar el mismo cálculo con el tercer\nnivel y así sucesivamente hasta terminar con todos los niveles o hasta que la diferencia\nentre niveles no pueda ser colocada en las abscisas.\n\n \n\nVer\ndiagramas  en La Gaceta impresa N° 201 del 19\nde octubre del 2005.\n\n \n\n(NOTA\nDE SINALEVI: el diagrama anterior fue corregido mediante FE DE ERRATAS de la\nGaceta N° 81 del 27 de abril del 2006).\n\nArtículo 8º-Informe. Las\nmediciones deberán acompañarse de un informe técnico, elaborado por las\nautoridades de salud, previo estudio del expediente. Este informe comprenderá\nlo siguiente:\n\n \n\na) Nombre del establecimiento,\nnombre de la persona física propietaria de la fuente emisora de ruido o el\nnombre de su representante legal.\n\n \n\nb) En caso de la atención de\ndenuncia agregar: nombre del denunciante y distancia de la empresa o persona\nfísica que emite el ruido y la ubicación de la (s) vivienda (s) afectada (s) u\notro (s) establecimiento (s) afectado (s) como hospitales, escuelas, centros\ncomerciales y otros.\n\n \n\nc) Nombre y número de pasaporte o\ncédula de la persona física o jurídica propietaria de la fuente emisora de\nruido.\n\n \n\nd) Fecha de elaboración del informe\ny nombre de la dependencia de salud que atiende la denuncia (Nivel Central,\nRegional o Local).\n\n \n\ne) Identificación de otras fuentes\nde ruido que influyan en la medición.\n\n \n\nf) Mencionar los sitios de medida en\nla(s) vivienda(s) u establecimiento(s) afectado(s).\n\n \n\ng) Tipo, marca, modelo y número de\nserie del aparato de medida. Indicar certificado de calibración.\n\n \n\nh) Verificar y ajustar la\ncalibración del equipo en caso necesario.\n\n \n\ni) Escala de ponderación y\natenuación empleada.\n\n \n\nj) Tipo de ruido (impulso, continuo\no fluctuante).\n\n \n\nk) Fecha, hora y datos\nmeteorológicos.\n\n \n\nl) Características de la fuente\nemisora.\n\n \n\nm) Número de mediciones efectuadas.\n\n \n\nn) Mediciones obtenidas de la fuente\ngeneradora más ruido de fondo.\n\n \n\no) Mediciones obtenidas del ruido de\nfondo (en caso que se requiera).\n\n \n\np) Resultado de los cálculos\ngenerados por el procesamiento de los datos de las mediciones.\n\n \n\nq) Conclusiones y recomendaciones.\n\nArtículo 9º-Acciones correctivas.\nEn caso de que los resultados del artículo anterior indiquen que el ruido\nproducido por la(s) fuente(s) emisora(s) sobrepasa(n) lo establecido por la\nnormativa jurídica vigente, el Ministerio de Salud procederá a girar la Orden\nSanitaria correspondiente al propietario o representante legal de la fuente\nemisora que incluya al menos lo siguiente:\n\n \n\na) Plan de confinamiento de ruido\ncon su memoria de cálculo y cronograma de actividades.\n\n \n\nb) Planos constructivos para su\nvisado sanitario en caso de ser necesario.\n\n \n\nc) Plazo para la presentación de los\npuntos a) y b).\n\n \n\nEn caso de que los resultados del\nartículo anterior indiquen que el ruido producido por la fuente(s) emisora(s)\nno sobrepasa(n) lo establecido en la legislación vigente, el Ministerio de\nSalud procederá a comunicarlo al denunciante.\n\nArtículo 10.-Vigencia. El presente\nReglamento rige a partir de la fecha de su publicación en el Diario Oficial La\nGaceta.\n\n \n\nDado en la Presidencia de la\nRepública.-San José, a los nueve días del mes de agosto del dos mil cinco.",
  "body_en_text": "in the entirety of the text\n\n                    -\n\n                        Complete Text of Norm 32692\n\n                        Procedure for the Measurement of Noise\n\nComplete Text record: 1710F0\nNo. 32692\n\nNo. 32692\n\n(This executive decree was repealed by Article\n39 of the Regulation for the control of environmental noise, approved by\nExecutive Decree No. 44486 of January 17, 2024)\n\nTHE PRESIDENT OF THE\nREPUBLIC\n\nAND THE MINISTRY OF HEALTH\n\n \n\nIn use of the\npowers conferred by Articles 50, 140; subsections 3) and 18) and 146 of\nthe Political Constitution; 2, 4, 7, 37, 38, 263, 293, 325, 337, 338, 339,\n340, 341, 342, 347, 348, 349, 355, 357, 363, 364 and concordant articles of Law No.\n5395 of October 30, 1973, \"Ley General de Salud\"; 6 of Law\nNo. 5412 of November 8, 1973, \"Ley Orgánica del Ministerio de\nSalud\"; 25, subsection 1) and 28, subsection b) of Law No. 6227 of May 2,\n1978, \"Ley General de Administración Pública\".\n\n \n\nConsidering:\n\n \n\n1st-That the health of the\npopulation is a public interest asset protected by the State.\n\n2nd-That it is the function of the\nMinistry of Health to issue the pertinent regulatory provisions, especially those related to the contribution, promotion, and maintenance\nof the conditions of the natural environment and artificial environments that\nallow for guaranteeing the vital and health needs of the population.\n\n3rd-That every person,\nnatural or legal, is subject to the mandates of the Ley General de Salud, its\nregulations, and the general and specific, ordinary and\nemergency orders that the health authorities issue in the exercise of their\ncompetencies.\n\n4th-That sonic measurement\nconstitutes the ideal technical means and reliable proof for verifying\nthe existence of noises that may affect the health of the population, and therefore\nit is necessary to employ methods that guarantee that the values obtained are\nreliable and allow for correct and accurate decisions on the matter.\n\n5th-That it is\nnecessary and timely to establish a procedure for measuring noise.\n\n6th-That Executive\nDecree No. 18209-S published in the Official Gazette La Gaceta No. 133 of\nJuly 13, 1988, which in turn reformed Articles 6 and 50 of Executive Decree No.\n11492-S of April 22, 1980 (Regulation on Industrial Hygiene) stated\nthat the current Dirección de Protección al Ambiente Humano of the Ministry\nof Health will establish the procedures in accordance with the established standards\nfor carrying out measurement tests. Therefore,\n\n \n\nTHEY DECREE:\n\n \n\nProcedure\nfor the Measurement of Noise\n\n \n\nArticle 1-Objective\nand Scope. For the purposes of application by the health authorities, officialize\nthe procedures for the measurement of noise that must be carried out with\nthe purpose of ensuring the protection of the health of persons with respect\nto contaminating emission of noise, originating from artificial sources.\n\nArticle 2-Competence of\nApplication. The application of this Regulation is the competence of the\nhealth authorities.\n\nArticle 3-Definitions.\nFor the purposes of this Regulation, the following shall be understood as:\n\n \n\na) Health Authority:\nMinistry of Health.\n\n \n\nb) Calibration Certificate:\nDocument issued by the Parent Company or Accredited Laboratory certifying\nthat the equipment has been inspected and its electronic deviations are\nwithin the limits specified by their manufacturers and comply\nwith ANSI and IEC standards. It is valid for one year.\n\n \n\nc) Noise Pollution:\nAny sound emission that adversely affects the health of human\nbeings.\n\n \n\nd) dB(A): It is the unit of\nmeasurement of the sound level when the A-weighting scale is used.\n\n \n\ne) Decibel (dB):\nDimensionless unit used to express the logarithm of the ratio between a\nmeasured quantity and a reference quantity. In this way, the dB is used\nto describe levels of sound pressure, power, or intensity.\n\n \n\nf) DPAH: Dirección de\nProtección del Ambiente Humano of the Ministry of Health.\n\n \n\ng) Emission: Emanation of\nnoise into the atmosphere by an emitting source.\n\n \n\nh) Emitting Source: Any\nobject or artifact that originates a sound wave, whether stationary,\nmobile, or portable.\n\n \n\ni) Sound Pressure Level (nivel de presión sonora, Lp):\nIt is defined by: Lp= 20 log P1/Po (dB) where:\n\n \n\nP1= Existing acoustic pressure\n(measured effective pressure)\n\n \n\nPo = Reference acoustic pressure=\n2 x 10-5 Pascals (Pa)= 20 micropascals (uPa).\n\n \n\nj) Noise Measurement:\nTechnical operation consisting of determining the values of noise levels\noriginating from one or several emitting sources.\n\n \n\nk) Noise Level: The\nsound pressure level measured using the measurement characteristics and\nA, B, or C scales, as specified by the \"American National Standards Institute\" (ANSI),\n\"Specification for Sound Level Meters\", latest revision.\n\n \n\nl) Sound Waves: They are waves\nthat are produced when the air is perturbed and travel through three-dimensional\nspace commonly as progressive longitudinal sinusoidal waves.\nThe propagation of sound waves implies the transfer of energy\n(partially kinetic and partially potential) through space.\n\n \n\nm) Person: Every person,\nphysical or legal, or group of private or public persons.\n\n \n\nn) Noise Confinement Plan (plan de confinamiento de ruido):\nConsists of those actions or corrective measures tending to encapsulate,\nabsorb, or diminish the noise within the emitting source in order not to affect\nthird parties.\n\n \n\no) Noise: Sound or a set\nof mixed and disorderly sounds, undesirable or disturbing that affects\nhuman beings psychologically, physically, or in any other way, or that exceeds\nthe established regulatory limitations.\n\n \n\np) Background Noise: It is the noise from\nall sources other than the specific sound source of interest (sounds\ndifferent from the one being measured).\n\n \n\nq) Continuous Noise: It is that\nwhich does not have rapid or sudden changes in level. It is characterized by\nsound pressure levels that do not fluctuate rapidly over time. The fluctuations\noccur at a rate of a few dB/second. Example: rotating machines, looms.\n\n \n\nr) Intermittent Noise:\nNoise that is interrupted, ceases, or repeats.\n\n \n\ns) Impact Noise: Noise\nthat is caused by single blows of short duration.\n\n \n\nt) Sound: A physical\nalteration in a medium (e.g., air) that can be detected by the human\near.\n\n \n\nu) Sound Level Meter (Sonómetro): Instrument\nused to measure sound levels.\n\nArticle 4-Prerequisites prior to\nthe Noise Measurement.\n\n \n\na) Identify and locate the\naffected person(s) in order to coordinate the time and place for conducting\nthe sonic measurements.\n\n \n\nb) Have measurement equipment\n(sound level meter) and its respective calibrator.\n\n \n\nc) Sonic measurements must be\ncarried out by a minimum of two officials of the Ministry of Health.\n\nArticle 5-Calibration of the\nEquipment. Before carrying out the measurement, it must be verified that the\nequipment has a current Calibration Certificate.\n\nThe equipment must be calibrated before\nthe measurement, for which the corresponding calibrator is used.\n\nCalibration should preferably be performed\nin an environment where no background noise is being generated,\nfollowing the manufacturer's instructions indicated in the equipment manual.\n\nAll measurement and\ncalibration equipment must have its respective manual for its operation.\n\nArticle 6-Of the Measurements.\nThe officials responsible for the sonic measurements of the Ministry of Health\nmust comply with at least the following aspects when conducting the\nmeasurements:\n\n \n\na) Before conducting any type\nof measurement, the full name and identity card number or passport number of the persons present during the measurements must be determined.\n\nRecord the date and start and end time of the measurements.\n\n \n\nb) Identify the source(s)\ngenerating the noise to be measured.\n\n \n\nc) If the noise is continuous, one must\nuse the slow attenuation (slow) and the fast attenuation (fast) shall be used\nfor measurements of short duration (e.g., church bells,\nsirens, alarms, and similar). If the noise is impact noise, one must use\nthe peak attenuation (peak) following the instructions of the Equipment Operation Manual. The sound level meter must be placed at an approximate height of 1.5 m from\nthe ground level, and the angle formed between the sound level meter and an inclined plane parallel\nto the ground must be between 30 and 60 degrees.\n\n \n\nd) Place the sound level meter at a\nminimum approximate free distance of 0.50 m from the official's body.\n\n \n\ne) In external measurements, the\nanti-wind screen (grid or filter) that is part of the equipment must be used.\n\n \n\nf) When conducting the measurements,\nextreme meteorological conditions such as rain, wind,\nlightning, and others that may affect the results obtained and the equipment must be avoided.\n\n \n\ng) It must be ensured that the\nmeasurements are conducted inside the buildings, avoiding sound-emitting sources\nunrelated to the measurement. The measurement must be conducted with the windows\nopen, and the site(s) of the property where they were performed must be indicated.\n\n \n\nh) Each measurement must be taken\nevery 15 seconds.\n\n \n\ni) At least 15\nmeasurements must be taken and the corresponding results recorded.\n\nj) Those\nmeasurements that include occasional noises (among others: motorcycles with\nopen exhaust, ambulance or fire truck sirens) must be discarded.\n\n \n\nk) Conduct ambient noise\nmeasurements, for which the source being evaluated must remain inactive.\n\n \n\nl) The measurements, in case of\nrepetition, must be conducted under conditions similar to those under which they were previously made.\n\nArticle\n7—Calculation of Sound Pressure Levels. When sound pressure levels from different emitting sources affect a single receiver and it\nis required to know the result of their sum, the properties of logarithms must be used.\n\nFor\ncalculation purposes, the following methods shall be used:\n\n \n\na)\nNumerical\nmethod: The magnitude of the sound pressure level in decibels (dB) is given by the expression:\n\n \n\nSee\nformulas in printed La Gaceta No. 201 of October 19, 2005.\n\n \n\nPractical\nexample:\n\n \n\nTo\ncalculate the sound pressure levels, proceed as follows:\n\n \n\nN1 = 101 dB\n\n \n\nN2 = 84 dB\n\n \n\nN3 = 91 dB\n\n \n\nN4 = 97 dB\n\n \n\nN5 = 100 dB\n\n \n\nN6 = 101 dB\n\n \n\nN7 = 99 dB\n\n \n\nApplying\nthe previously defined expression to each sound pressure level yields the following\nvalues:\n\n \n\nSee\nformulas in printed La Gaceta No. 201 of October 19, 2005.\n\n \n\nb) Graphical\nMethod: If there are several sound pressure levels and one wants to know the sum\nof these, using Figure 1, proceed as follows:\n\n \n\n1. The\nlevels are ordered from highest to lowest.\n\n \n\n2. The\ndifference between the first and the second is obtained.\n\n \n\n3. The\ndifference obtained is taken to the x-axis of the curve, obtaining on the y-axis the\nvalue that must be added to the higher level.\n\n \n\n4. With\nthis sum-level, thus obtained, the same calculation is performed with the third\nlevel, and so on until all levels are processed or until the difference\nbetween levels cannot be placed on the x-axis.\n\n \n\nSee\ndiagrams in printed La Gaceta No. 201 of October 19,\n2005.\n\n \n\n(NOTE\nFROM SINALEVI: the previous diagram was corrected via ERRATA in\nLa Gaceta No. 81 of April 27, 2006).\n\nArticle 8-Report. The\nmeasurements must be accompanied by a technical report, prepared by the\nhealth authorities, after studying the file. This report will include\nthe following:\n\n \n\na) Name of the establishment,\nname of the individual owner of the noise emitting source or the\nname of their legal representative.\n\n \n\nb) In the case of handling a\ncomplaint, add: name of the complainant and distance from the company or individual\nthat emits the noise and the location of the affected dwelling(s) or\nother affected establishment(s) such as hospitals, schools, shopping\ncenters, and others.\n\n \n\nc) Name and passport or\nID number of the individual or legal entity owning the noise emitting source.\n\n \n\nd) Date of report preparation\nand name of the health unit handling the complaint (Central, Regional, or Local Level).\n\n \n\ne) Identification of other\nnoise sources that influence the measurement.\n\n \n\nf) Mention the measurement sites in the\naffected dwelling(s) or establishment(s).\n\n \n\ng) Type, brand, model, and serial\nnumber of the measurement device. Indicate the calibration certificate.\n\n \n\nh) Verify and adjust the\nequipment calibration if necessary.\n\n \n\ni) Weighting scale and\nattenuation used.\n\n \n\nj) Type of noise (impulse, continuous,\nor fluctuating).\n\n \n\nk) Date, time, and meteorological\ndata.\n\n \n\nl) Characteristics of the emitting\nsource.\n\n \n\nm) Number of measurements taken.\n\n \n\nn) Measurements obtained from the generating\nsource plus background noise.\n\n \n\no) Measurements obtained from the background\nnoise (if required).\n\n \n\np) Result of the calculations\ngenerated by processing the measurement data.\n\n \n\nq) Conclusions and recommendations.\n\nArticle 9-Corrective actions.\nIf the results of the preceding article indicate that the noise\nproduced by the emitting source(s) exceeds what is established by the\ncurrent legal regulations, the Ministry of Health will proceed to issue the corresponding\nSanitary Order to the owner or legal representative of the emitting\nsource, which includes at least the following:\n\n \n\na) Noise confinement plan (plan de confinamiento de ruido)\nwith its calculation report and activity schedule.\n\n \n\nb) Construction blueprints for their\nsanitary approval, if necessary.\n\n \n\nc) Deadline for the presentation of\nitems a) and b).\n\n \n\nIf the results of the\npreceding article indicate that the noise produced by the emitting source(s)\ndoes not exceed what is established in current legislation, the Ministry of\nHealth will proceed to notify the complainant.\n\nArticle 10.-Effectiveness. This\nRegulation takes effect as of the date of its publication in the Official Gazette La\nGaceta.\n\n \n\nGiven at the Presidency of the\nRepublic.-San José, on the ninth day of August of two thousand five."
}